Dieser Inhalt ist für Deutschland bestimmt. Unser System hat erkannt, dass Sie aus USA kommen. Wollen Sie USA als neues Land setzen?

SILPURAN® 4200

SILPURAN® 4200 is a non-slump to self-levelling silicone rubber formulation, curing at room temperature under the influence of atmospheric moisture to a silicone elastomer exhibiting good mechanical properties.

SILPURAN® 4200 is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY.



Eigenschaften

SILPURAN® 4200 meets selected test requirements of ISO 10993 and United States Pharmacopeia (USP) Class VI. It usually exhibits good primerless adhesion to many substrates, e.g. glass, ceramics, metals, plastics and powder coatings. The recommended service temperature range is approx. -50 °C to +180 °C.

Spezifische Merkmale von SILPURAN® 4200

  • Regulatorisch: Lebensmittelkontakt
  • Spezifische Merkmale: kondensationsvernetzend
  • Spezifische Merkmale: Lebensmittelkontakt
  • Vernetzungseigenschaft: 1-komponentiges System
  • Vernetzungseigenschaft: kondensationsvernetzend

Disclaimer

Alle unsere Angaben beruhen auf bestem Wissen. Allerdings übernehmen wir hierfür keine Haftung oder Gewährleistung und behalten uns jederzeit technische Änderungen vor. Es liegt in der eigenen Verantwortung des Käufers, die Angaben sowie die Geeignetheit unseres Produktes für den vorgesehenen Einsatzzweck vor dem Gebrauch zu überprüfen. Vertragliche Regelungen gehen immer vor. Der Gewährleistungs- und Haftungsausschluss gilt - insbesondere im Ausland - auch im Hinblick auf Schutzrechte Dritter.

One-component silicone adhesive, in particular for medical applications.

The following studies were performed on vulcanizates of SILPURAN® 4200 according to ISO 10993:
    - Cytotoxicity (ISO 10993-5)
    - Sensitation (ISO 10993-10)

The following studies were performed on vulcanizates of SILPURAN® 4200 according to USP class VI:
    - Acute systemic toxicity
    - Intracutaneous toxicity
    - Implantation test
No adverse effects have been detected at any of the studies performed.

 

Properly cured vulcanizates of SILPURAN® 4200 can be used for food contact applications and are suitable for use under the Recommendation "XV. Silicones" of the BfR as well as FDA 21 CFR § 175.300 "Resinous and polymeric coatings" and FDA 21 CFR §177.2600 "Rubber articles intended for repeated use" considering any given limitations on extractable and volatile substances.

SILPURAN® 4200 is a ready-to-use, one-part silicone rubber which starts curing when exposed to air moisture.

  -   Skin-forming time at 23 °C, 50 % RH:  5 - 10 min
  -   Curing time at 23 °C, 50 % RH: 12 h/mm

As RTV-1 silicones require humidity for curing, free access of air moisture to the silicone rubber is essential. The vulcanization time of SILPURAN® 4200 can be greatly reduced by increasing the level of air's relative humidity. Please note that, unlike the initial skin formation, the total curing rate of RTV-1 silicones is limited by moisture's diffusion speed in the silicone rubber. Since increasing the curing temperature has just a minor effect on both, the skin forming time as well as the curing speed, SILPURAN® 4200 is typically vulcanized at room temperature. Heat curing is recommended only for applications where the silicone rubber is applied as a thin film (thickness less than 0.5 mm), because otherwise blistering is likely to occur due to the quick release of acetic acid.


Detailed information about the processing of RTV-1 silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend preliminary tests to optimize conditions for the particular application.

 


Removal:
If removal of the silicone from machines or dispensing equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone rubber is fully vulcanized. Cured silicone needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.

Verpackung / Gebinde

SILPURAN® 4200 is available in 310 mL cartridges. SILPURAN® is neither produced nor packed under sterile conditions, so the final product has to be sterilized prior to use, if necessary.

Lagerung

Store cartridges in a dry and cool place. The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemie AG
Heilbronner Strasse 74
70191 Stuttgart
Deutschland
+49  711  61942-0 (Phone)
+49 711 61942-61  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Sie möchten ein Produktmuster?

Hier können Sie ein Produktmuster anfordern.

Muster anfordern

Mehr Produkte

Produkte Technische Daten
dynamische Viskosität Weiterreißwiderstand Härte Shore A Reißfestigkeit Reißdehnung
SILPURAN® 4200 250000 mPa·s[2] 250000 mPa·s[2] 10 N/mm[1] 10 N/mm[1] 35[3] 35[3] 5,5 N/mm²[4] 5,5 N/mm²[4] 300 %[5] 300 %[5]
Legend
[1] Weiterreißwiderstand | ASTM D 624,  [2] dynamische Viskosität (0.5 s⁻ ¹) | 23 °C | DIN EN ISO 3219,  [3] Härte Shore A | DIN 53505 / ISO 868,  [4] Reißfestigkeit | DIN 53504 S1 / ISO 37,  [5] Reißdehnung | DIN 53504 S1 / ISO 37 

Bestellen

Meine Medien


Meine Favoriten

Meine Produkte