SILPURAN® 2114 A/B

Two-component, addition-curing silicone composition curing to a soft silicone adhesive with high adhesive strength



Properties

  • biocompatible, certificates of compatibility with USP Class VI and ISO 10993 available on request
  • no by-products from curing process
  • medium viscosity, easily pourable
  • very good adhesion, typical value 3.5 N/2.5 cm (90° peel test, on stainless steel)
  • high transparency

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

SILPURAN® 2114 A/B can be used as a skin adhesive in medical applications.

Components A and B of SILPURAN® 2114 A/B are mixed homogeneously in a ratio A : B = 1 : 1 and vulcanize rapidly at temperatures over 100 °C.

SILPURAN® 2114 A/B has good adhesive properties that can be adjusted to suit the relevant requirements:

Increasing the proportion of component A results in a softer vulcanisate and increased tackiness. Increasing the proportion of component B results in a harder vulcanisate and reduced tackiness.

Important note:
The platinum catalyst is contained in component A.

Caution:
Only components A and B with the same lot number may be processed together!

 

Storage

The 'Best use before end' date of each batch is shown on the product label.

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker Chemical Corporation
3301 Sutton Road
Adrian, MI 49221-9397
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Viscosity, dynamic Penetration
SILPURAN® 2100 A/B 34000 mPa·s[1] 34000 mPa·s[1] 205 1/10mm[2] 205 1/10mm[2]
SILPURAN® 2110 A/B 54000 mPa·s[1] 54000 mPa·s[1] 200 1/10mm[2] 200 1/10mm[2]
SILPURAN® 2112 A/B 11600 mPa·s[1] 11600 mPa·s[1] 225 1/10mm[3] -
SILPURAN® 2114 A/B 12000 mPa·s[1] 12000 mPa·s[1] 200 1/10mm[2] 200 1/10mm[2]
SILPURAN® 2117 A/B 33000 mPa·s[1] 33000 mPa·s[1] 205 1/10mm[4] -
SILPURAN® 2120 A/B 31000 mPa·s[1] 31000 mPa·s[1] 120 1/10mm[5] -
SILPURAN® 2122 A/B 2500 mPa·s[1] 2500 mPa·s[1] 180 1/10mm[6] -
SILPURAN® 2130 A/B 1000 mPa·s[1] 1000 mPa·s[1] 220 1/10mm[2] 220 1/10mm[2]
Legend
[1] Viscosity, dynamic | DIN EN ISO 3219,  [2] Penetration | DIN ISO 2137 | hollow cone of 62.5 g, 60 s, curing time 60 min at 120 °C,  [3] Penetration | DIN ISO 2137 | hollow cone of 62.5 g, 60 s, curing conditions 60 min at 120 °C,  [4] Penetration | DIN ISO 2137 | (hollow cone of 62.5 g, 60 s, curing time 60 min at 120 °C,  [5] Penetration | hollow cone of 62.5 g, curing time 60 min at 120 °C,  [6] Penetration | hollow cone of 62.5 g, 60 s, curing time 60 min at 120 °C 

Order

My media


My favorites

My products