WACKER® GP - GENERAL PURPOSE (ZJG)
WACKER® GP - GENERAL PURPOSE (ZJG) is a one-component, acid-curing, silicone sealant for general purpose sealing.
WACKER® GP - GENERAL PURPOSE (ZJG) cures at room temperature in the presence of atmospheric moisture to give a permanently flexible silicone rubber.
- rapid crosslinking: quickly becomes tack-free
- adheres excellently to glass, vitrified surfaces, ceramic tiles, selected plastics and most coatings
- ready gunnability at low (+ 5 °C) and high (+ 40 °C) temperatures
- flexible at low (- 40 °C) and high temperatures (+ 100 °C)
- DIY applications (car, boat, caravan, house)
- Suitable for many general industrial sealing and bonding uses
The substrate areas that will be in contact with the sealant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth.
For application from cartridges cut thread open, fix nozzle on top and cut to required bead size. The sealant can be applied in beads or layers. It requires moisture in order to cure.
The curing time can take longer at lower temperatures, lower humidity or by low volume of air exchange.
WACKER® GP - GENERAL PURPOSE (ZJG) exhibits excellent primerless adhesion to many non-porous siliceous materials, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker varnished or painted wood as well as selected plastics and coatings
Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service.
Restrictions on use
It is the user's responsibility to test the compatibility of the sealant with the adjoining materials. Incompatible substances like coating materials (paints, varnishes and glazes) or organic plasticizer containing rubbers (EPDM, butyl and neoprene) can lead to discoloration or other impairments like loss of adhesion of the sealant. Materials in direct contact with the applied sealant like cleaning agents and materials in indirect contact like gaseous emissions can damage the sealant in its function or change its appearance. Because of the multitude of these materials. Wacker cannot make a general statement to the compatibility of materials with the sealant. In case of doubt the user shall conduct appropriate preliminary tests.
WACKER® GP - GENERAL PURPOSE (ZJG) must not be used for insulating glass applications.
WACKER® GP - GENERAL PURPOSE (ZJG) should not be used on substrates such as concrete, fibrous cement, and mortar, as the product releases acetic acid during vulcanization.
WACKER® GP - GENERAL PURPOSE (ZJG) should not be used in contact with metals such as lead, copper, brass or zinc due to corrosion.
WACKER® GP - GENERAL PURPOSE (ZJG) should not be used in contact with prestressed polyacrylate elements as it may cause stress cracking.
WACKER® GP - GENERAL PURPOSE (ZJG) may be discolored in contact with some organic elastomers, e.g. EPDM, APTK and neoprene.
WACKER® GP - GENERAL PURPOSE (ZJG) must not be used for sealing of aquaria. WACKER® 121 - AQUARIUM has been specifically developed for aquarium applications.
WACKER® GP - GENERAL PURPOSE (ZJG) is not recommended for use on natural stone, such as marble, granite, quartzite, as it can cause staining. In this case use an alternative grade such as WACKER® 460 - NATURAL STONE.
WACKER® GP - GENERAL PURPOSE (ZJG) is not recommended for structural glazing bonding.
WACKER® GP - GENERAL PURPOSE (ZJG) is not recommended for sealing of aquaria or for longer-term use under water. WACKER® 120 – FOOD AND WATER has been specifically developed for aquarium applications.
WACKER® GP - GENERAL PURPOSE (ZJG) is not suitable for food grade applications where the joints are likely to come in contact with food.
WACKER® GP - GENERAL PURPOSE (ZJG) is not suitable for use as a mirror adhesive.
The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange.
The use of tooling agents should be avoided if possible. Otherwise, water or a diluted solution of a little neutral soap or alcohol in water should be sparingly applied.