POWERSIL® 466 LV A/B

POWERSIL® 466 LV A/B is a liquid silicone rubber with medium conductivity and excellent mechanical properties.



Properties

  • ready-to-use, two-component system
  •  high elongation at break, low tension set
  •  stable electrical properties
  •  good mechanical properties

Specific features of POWERSIL® 466 LV A/B

  • Product Rheology: Low viscosity
  • Specific Features: Cold-shrinkable
  • Specific Features: Electrically conductive
  • Specific Features: Low viscosity
  • Vulcanizate: Electrically conductive

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

POWERSIL® 466 LV A/B is suitable for production of electrically conductive injection moulded articles, especially cable accessories in the medium and high voltage range.
The range of use spreads from push-on accessories to cold shrink applications. POWERSIL® 466 LV A/B combines a low Shore A durometer with high elongation, good setting properties (low tension set) and good mechanical properties which are a must for cold shrink applications.

POWERSIL® 466 LV A/B is a low viscosity LSR that shows excellent processing properties.

Components A and B are delivered ready to use in drums of 20 and 200 litres capacity. They can be pumped by means of standard metering equipment from these drums and mixing in a static mixer straight into the heated mold.

The mixing ratio is 1 : 1. At room temperature, mixtures of A and B components have a pot life of at least three days.

For detailed information, refer to brochures on www.wacker.com.

Storage

The 'Best use before end' date of each batch is shown on the product label.

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker Chemical Corporation
3301 Sutton Road
Adrian, MI 49221-9397
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Appearance Hardness Shore A Tensile strength Elongation at break Tear strength Compression Set
ELASTOSIL® LR 3002/35 A/B colourless colourless 33[1] 33[1] 7.0 N/mm²[2] 7.0 N/mm²[2] 460 %[3] 460 %[3] 25 N/mm[4] 25 N/mm[4] - -
ELASTOSIL® LR 3003/20 TR A/B transparent transparent 22[1] 22[1] 8.3 N/mm²[2] 8.3 N/mm²[2] 870 %[3] 870 %[3] 24 N/mm[4] 24 N/mm[4] 17 %[5] 17 %[5]
ELASTOSIL® LR 3003/30 A/B transparent transparent 31[1] 31[1] 7.5 N/mm²[2] 7.5 N/mm²[2] 620 %[3] 620 %[3] 23 N/mm[4] 23 N/mm[4] 10 %[5] 10 %[5]
ELASTOSIL® LR 3003/40 A/B transparent transparent 40[1] 40[1] 10.0 N/mm²[2] 10.0 N/mm²[2] 610 %[3] 610 %[3] 30 N/mm[4] 30 N/mm[4] 11 %[5] 11 %[5]
ELASTOSIL® LR 3003/50 A/B transparent transparent 50[1] 50[1] 10.3 N/mm²[2] 10.3 N/mm²[2] 490 %[3] 490 %[3] 28 N/mm[4] 28 N/mm[4] 13 %[5] 13 %[5]
ELASTOSIL® LR 3003/60 A/B transparent transparent 60[1] 60[1] 9.5 N/mm²[2] 9.5 N/mm²[2] 340 %[3] 340 %[3] 27 N/mm[4] 27 N/mm[4] 12 %[5] 12 %[5]
ELASTOSIL® LR 3003/70 A/B transparent transparent 70[1] 70[1] 8.6 N/mm²[2] 8.6 N/mm²[2] 290 %[3] 290 %[3] 20 N/mm[4] 20 N/mm[4] 12 %[5] 12 %[5]
ELASTOSIL® LR 3004/40 A/B transparent transparent 40[1] 40[1] 10.0 N/mm²[2] 10.0 N/mm²[2] 610 %[3] 610 %[3] 35 N/mm[4] 35 N/mm[4] 10 %[5] 10 %[5]
ELASTOSIL® LR 3005/60 A/B transparent transparent 60[1] 60[1] 9.5 N/mm²[2] 9.5 N/mm²[2] 380 %[3] 380 %[3] 28 N/mm[4] 28 N/mm[4] 18 %[6] -
ELASTOSIL® LR 3043/40 A/B transparent transparent 40[1] 40[1] 10 N/mm²[2] 10 N/mm²[2] 680 %[3] 680 %[3] 36 N/mm[4] 36 N/mm[4] 25 %[5] 25 %[5]
POWERSIL® 464 A/B - - 50[1] 50[1] 7.0 N/mm²[2] 7.0 N/mm²[2] 350 %[3] 350 %[3] 25 N/mm[4] 25 N/mm[4] - -
POWERSIL® 466 A/B - - 38[1] 38[1] 7.0 N/mm²[2] 7.0 N/mm²[2] 650 %[3] 650 %[3] 28 N/mm[4] 28 N/mm[4] 11 %[5] 11 %[5]
POWERSIL® 466 LV A/B - - 32[1] 32[1] 7.0 N/mm²[2] 7.0 N/mm²[2] 650 %[3] 650 %[3] 20 N/mm[4] 20 N/mm[4] 11 %[5] 11 %[5]
POWERSIL® 730 A/B - - 35[1] 35[1] 8.0 N/mm²[2] 8.0 N/mm²[2] 600 %[3] 600 %[3] 26 N/mm[4] 26 N/mm[4] - -
POWERSIL® 732 CS A/B - - 33[1] 33[1] 9.0 N/mm²[2] 9.0 N/mm²[2] 750 %[3] 750 %[3] 35 N/mm[4] 35 N/mm[4] - -
POWERSIL® 735 LIGHTGRAY A/B - - 39[1] 39[1] 8.0 N/mm²[2] 8.0 N/mm²[2] 500 %[3] 500 %[3] 30 N/mm[4] 30 N/mm[4] - -
POWERSIL® 740 DARK GRAY A/B - - 40[1] 40[1] 9.8 N/mm²[2] 9.8 N/mm²[2] 650 %[3] 650 %[3] 35 N/mm[4] 35 N/mm[4] - -
POWERSIL® 740 LIGHTGRAY A/B - - 40[1] 40[1] 9.8 N/mm²[2] 9.8 N/mm²[2] 650 %[3] 650 %[3] 35 N/mm[4] 35 N/mm[4] - -
POWERSIL® XLR® 630 A/B - - 35[1] 35[1] 7.0 N/mm²[2] 7.0 N/mm²[2] 450 %[3] 450 %[3] 25 N/mm[4] 25 N/mm[4] - -
Legend
[1] Hardness Shore A | DIN ISO 48-4,  [2] Tensile strength | ISO 37 type 1,  [3] Elongation at break | ISO 37 type 1,  [4] Tear strength | ASTM D 624 B,  [5] Compression Set | 22 h | 175 °C | DIN ISO 815-1 type B method A | post-cured 6 h / 200 °C,  [6] Compression Set | 22 h | 175 °C | DIN ISO 815-1 type B method A 

Order

My media


My favorites

My products