VINNAPAS® CEZ 3031

VINNAPAS® CEZ 3031 is a medium particle size, protective colloid-containing aqueous dispersion of a terpolymer of vinyl acetate, ethylene and vinyl chloride.

The principal feature of VINNAPAS® CEZ 3031 is its wide range of uses in coating systems containing opacifying pigments. The dispersion is low in odor and is produced without the use of alkyl phenol ethoxylate (APEO) containing compounds.

x



Properties

  • Great Versatility
  • High Elasticity
  • Very good saponification resistance
  • Due to the low favorable minimum film forming temperature of  approx. +2°C there is no need to use coalescent agents with VINNAPAS® CEZ 3031

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

VINNAPAS® CEZ 3031 has proved to be an outstanding binder in many fields of application and versatility is its special strength.

VINNAPAS® CEZ 3031 is particularly recommended to produce masonry paints with good hiding power and great flexibility.

Thanks to its good resistance to saponification, VINNAPAS® CEZ 3031 can be employed as the organic polymer component of organo-silicate paints and plasters. To ensure a good shelf life, the formulation must be carefully built around the binder.

To achieve optimum weathering resistance, opaque pigments should be used to ensure adequate pigmentation.

Due to its minimum film forming temperature of approx. +2°C VINNAPAS® CEZ 3031 doesn’t need any coalescence aids for filming and so it’s a very suitable binder for paints which complies with strict eco-labeling requirements.

VINNAPAS® CEZ 3031 has proved itsself as an excellent binder for synthetic resin plasters, especially in exterior insulation and finish systems (EIFS). In such a system, VINNAPAS® CEZ 3031 can also be used as binder for the styrene-panel adhesive and for the base coat. In other words, only one binder is needed for the entire system. The dispersion is readily compatible with Portland cement and hardly influences its setting time - a fact which is exploited to increase the water resistance of the adhesive and base coat. By virtue of the low flammability of VINNAPAS® CEZ 3031, correctly installed EIFS with this composition fall under Fire Class B as per EN 13501-1 (which applies to EIFS). Interior plasterwork based on VINNAPAS® CEZ 3031 does not require the use of film-forming agents and has the advantage of producing very little odor while being applied.

VINNAPAS® CEZ 3031 can be blended with the most anionic and/or nonionic aqueous polymer dispersions. However, the compatibility of the mixture should be tested by means of a storage test. This is because, despite good polymer compatibility, differences in the refractive indices sometimes cause cloudiness in the dry dispersion film.

VINNAPAS® CEZ 3031 is compatible with common pigments and extender and is easy to process.

VINNAPAS® CEZ 3031 forms a film (as per ISO 2115) at 2 °C and can therefore usually be processed - especially for interior applications - without the addition of film-forming agents.

If the product is used in applications other than those mentioned, the choice, processing and use of the product is the sole responsibility of the purchaser. All legal and other regulations must be complied with.

For questions concerning food contact status according the chapter 21 CFR (US FDA) and German BfR, please feel free to contact us.

Wacker Chemie AG
Hanns-Seidel-Platz 4
D-81737 München
Germany

Storage

When the dispersion is stored in tanks, proper storage conditions must be maintained. The product has a shelf life of 6 months starting from the date of receipt if stored in the original, unopened containers at temperatures between 5 and 30 °C. Any longer periods for the maximum storage period that may be described in the Certificate of Analysis which accompanies each shipment of the product, take preference over this suggestion in which case the time period stated in the Certificate of Analysis shall be solely authoritative. Iron or galvanized iron containers and equipment are not recommended. Corrosion could result in discoloration of the dispersion or blends made from it in further processing. We therefore recommend the use of containers and equipment made of ceramic, rubberized or enameled materials, appropriately finished stainless steel, or plastic (rigid PVC, polyethylene or polyester resin). As polymer dispersions may tend to superficial film formation, skins or lumps may be formed during storage or transportation. A filtration process is thus recommended prior to utilization of the product.

Preservation for Transport, Storage and further Processing

The product is adequately preserved during transportation and storage if kept in the original, unopened containers. However, if it is transferred to storage tanks, the dispersion should be protected against microbial attack by adding a suitable preservative package.

Measures should also be taken to ensure cleanliness of the tanks and pipes. In unstirred tanks, a layer of preservative-containing water should be sprayed onto the surface of the dispersion to prevent the formation of unwanted skin and possible attack by microorganisms. The thickness of this water layer should be < 5 mm for low viscosity dispersions and up to 10–20 mm for high viscosity products. Proper procedures – periodic tank cleaning and sanitization – must be set up in order to prevent microbial attack. Contact your biocide representative/supplier for further plant hygiene recommendations. Measures should be taken to ensure that only clean air enters the tank when the dispersion is removed.

Finished products manufactured from polymer dispersions usually also require preservation. The type and scope of preservation will depend on the raw materials used and the anticipated sources of contamination. The compatibility with other components and the efficacy of the preservative should always be tested in the respective formulation. Preservative manufacturers will be able to advise you about the type and dosage of preservative required.

Sales and support

Wacker Chemical Corporation
6870 Tilghman St
Allentown, PA 18106-9346
United States
+1  610  336-2700 (Phone)
+1 517 264-4088  (Fax)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Order

My media


My favorites

My products