VINNAPAS® 5043 N
VINNAPAS® 5043 N is a dispersible polymer powder for dry mix mortars, specifically suited for ETICS. It is based on a very flexible copolymer of vinyl acetate and ethylene and belongs to the product class VINNAPAS® N which means that it has a neutral effect on rheology and provides the basic properties adhesion and flexibility. VINNAPAS® 5043 N is part of our standard range, offering you the best-in-class solutions.
- VINNAPAS® 5043 N is a copolymer powder of vinyl acetate and ethylene and is dispersible in water.
- Because of its relatively high ethylene content, this resin is soft and flexible. Its glass transition temperature (Tg) is below the freezing point of water.
- Compounds modified with VINNAPAS® 5043 N exhibit improved adhesion, flexural strength, deformability, abrasion resistance and are easier to process. Leveling, thixotropy and water retention are essentially unaffected.
- The product is ideal for use in combination with other mortar additives intended to enhance specific properties.
- VINNAPAS® 5043 N contains a fine mineral filler as an antiblocking agent. It is produced without the addition of organic solvents, plasticizers and film-forming agents.
- VINNAPAS® 5043 N has no effect on rheological properties and is a dispersible polymer powder in the lower Tg range. It is suitable for formulating highly flexible compounds with very good adhesion to organic substrates (polystyrene) and end products with low emissions.
All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.
For typical application fields of VINNAPAS® 5043 N, refer to the section "application". Please discuss additional applications with your WACKER customer representative.
For the production of ready-mixed dry mortars, such as adhesives and patching compounds, blend VINNAPAS® 5043 N with the other dry ingredients in appropriate equipment. Temperatures should not be allowed to rise excessively during mixing because otherwise the dispersible polymer powder could agglomerate by virtue of its thermoplastic properties. The mortar is prepared for use by adding the recommended amount of water and mixing mechanically or by hand. Since hand mixing generates little shear force, we recommend allowing the fresh mortar to slake for 5 minutes and then stirring it again. This is usually unnecessary where mechanical mixers are employed.
If the product is used in applications other than those mentioned, the choice, processing and use of it is the sole responsibility of the purchaser. All legal and other regulations must be complied with.
Slight color variations of the polymer granulate may occure without impairing the product's functionality.
Big Bags or bulk on request.
Sales and support
How can we help you?
- Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Would you like a product sample?
You can request a product sample here.Request sample
|VINNAPAS® 4020 N||320 - 420 kg/m³ 320 - 420 kg/m³|
|VINNAPAS® 4045 E||250 - 400 kg/m³ 250 - 400 kg/m³|
|VINNAPAS® 4240 N||430 - 630 kg/m³ 430 - 630 kg/m³|
|VINNAPAS® 5044 N (USA)||400 - 550 kg/m³ 400 - 550 kg/m³|
|VINNAPAS® 5047 T||400 - 500 kg/m³ 400 - 500 kg/m³|
|VINNAPAS® 5048 H||400 - 550 kg/m³ 400 - 550 kg/m³|
|VINNAPAS® 7034 E||450 - 600 kg/m³ 450 - 600 kg/m³|
|VINNAPAS® 7055 E||370 - 520 kg/m³ 370 - 520 kg/m³|
|VINNAPAS® 8034 H||400 - 550 kg/m³ 400 - 550 kg/m³|
|VINNECO® 4023 N (GER)||470 - 570 kg/m³ 470 - 570 kg/m³|
|VINNECO® 5044 N (GER)||400 - 550 kg/m³ 400 - 550 kg/m³|