VINNAPAS® EP 8178

VINNAPAS® EP 8178 is a poly(vinyl alcohol) stabilized vinyl acetate-ethylene (VAE) copolymer dispersion with a glass transition temperature (Tg ) of approximately - 3 °C. It was developed as a high performance, ultra-high solids dispersion for weather-resistant air barriers with excellent water resistance, ideal mechanical properties and high extender loading capability.

 



Properties

VINNAPAS® EP 8178 is manufactured to an ultra-high solids content of 70 percent while maintaining a viscosity range of 1200-2700 mPa.s. This combination of high solids and moderate viscosity allows formulators to prepare very unique high solids products. The low Tg allows formulators to minimize the use of coalescents or plasticizers.

VINNAPAS® EP 8178 is produced without the use of any surfactants or defoamers that contain alkylphenol ethoxylates (APEOs). No formaldehyde or formaldehyde donors are intentionally added. 

Specific features

  • Breathability
  • Water resistance
  • Flexible and tough
  • Low VOC capable
  • Low formaldehyde content
  • Produced without APEO

 

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

Protect against frost.

Vapor Permeable Membranes

VINNAPAS® EP 8178  is vapor permeable in low- and high-humidity environments but remains resistant to bulk water, such as from wind-driven rain. Moreover, it provides excellent tensile strength and elongation at break, which is not diminished by immersion in water. This improves resistance to crack formation following exposure to weathering.

Liquid-applied barrier coatings can be easily sprayed or roller-applied to residential or commercial structures to form a continuous protective layer. VINNAPAS® EP 8178 can be used for creating high-solids, rapidly drying formulations with no additional plasticizers or coalescing agents.

 

Storage

When VINNAPAS® EP 8178 is stored in tanks, proper storage conditions must be maintained. If stored in the original, unopened containers at cool (below 30 °C), but frost-free temperatures VINNAPAS® EP 8178 has a shelf life of 9 months from the date of manufacture. Iron or galvanized-iron equipment and containers are not recommended because the dispersion is slightly acidic. Corrosion may result in discoloration of the dispersion or its blends when further processed. Therefore the use of containers and equipment made of ceramics, rubberized or enameled materials, appropriately finished stainless steel, or plastic (e.g. rigid PVC, polyethylene or polyester resin) is recommended. As polymer dispersions may tend to superficial film formation, skins or lumps may form during storage or transportation. Filtration is therefore recommended prior to utilization of the product.

Preservation for Transport, Storage and further Processing

VINNAPAS® EP 8178 is adequately preserved during transportation and storage if kept in the original, unopened containers. However, if it is transferred to storage tanks, the dispersion should be protected against microbial attack by adding a suitable preservative package. To maintain proper storage conditions appropriate measures should also be taken to ensure cleanliness of the tanks and pipes. In a storage tank in which VINNAPAS® EP 8178 is not stirred, it is advisable to contact your biocide representative/supplier. Proper procedures must be set up in order to prevent microbial attack between necessary periodic tank cleaning and sanitization. These procedures will vary, since loading and unloading practices in each storage situation will differ slightly. Finished products manufactured from polymer dispersions usually also require preservation. The type and scope of preservation will depend on the raw materials used and the anticipated sources of contamination. The compatibility with other components and the efficacy of the preservative should always be tested in the respective formulation. Preservative manufacturers will be able to advise you about the type and dosage of preservative required.

Sales and support

Wacker Chemical Corporation
6870 Tilghman St
Allentown, PA 18106-9346
United States
+1  610  336-2700 (Phone)
+1 517 264-4088  (Fax)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Order

My media


My favorites

My products