VINNAPAS® EZ 222
VINNAPAS® EZ 222 is a hydroxyethyl cellulose/surfactant stabilized vinyl acetate-ethylene (VAE) copolymer dispersion with a glass transition temperature (Tg) of +18.0°C.
- Excellent scrub resistance
- Good flow and leveling
- Low viscosity
- High solids content
- Produced without the use of APEOs
Protect against frost.
VINNAPAS® EZ 222 can be used in flat to mid-sheen DIY architectural coatings applications. It provides excellent scrub resistance and the large particle size provides good flow and leveling. Furthermore, the dispersion can be used in intumescent coatings formulations.
VINNAPAS® EZ 222 is manufactured without the use of any surfactants or defoamers that contain alkylphenol ethoxylates.
VINNAPAS® EZ 222 can be thickened using such materials as hydroxyethyl cellulose or polyacrylic acid-acrylamide copolymer resins. VINNAPAS® EZ 222 will accept high loadings of such fillers as calcium carbonate and clay without appreciably changing the viscosity.
When the dispersion is stored in tanks, proper storage conditions must be maintained. If stored in the original, unopened containers at cool (below 30 °C), but frost-free temperatures the product has a shelf life of 9 months from the date of manufacture. Any longer periods for the maximum storage period that may be described in the Certificate of Analysis which accompanies each shipment of the product, take preference over this suggestion in which case the time period stated in the Certificate of Analysis shall be solely authoritative. Iron or galvanized-iron equipment and containers are not recommended because the dispersion is slightly acidic. Corrosion may result in discoloration of the dispersion or its blends when further processed. Therefore, the use of containers and equipment made of ceramics, rubberized or enameled materials, appropriately finished stainless steel, or plastic (e.g. rigid PVC, polyethylene or polyester resin) is recommended. As polymer dispersions may tend to superficial film formation, skins or lumps may form during storage or transportation. Filtration is therefore recommended prior to utilization of the product.
Preservation for Transport, Storage and further Processing
The product is adequately preserved during transportation and storage if kept in the original, unopened containers. However, if it is transferred to storage tanks, the dispersion should be protected against microbial attack by adding a suitable preservative package. To maintain proper storage conditions appropriate measures should also be taken to ensure cleanliness of the tanks and pipes. In a storage tank in which the product is not stirred, it is advisable to contact your biocide representative/supplier. Proper procedures must be set up in order to prevent microbial attack between necessary periodic tank cleaning and sanitization. These procedures will vary, since loading and unloading practices in each storage situation will differ slightly. Finished products manufactured from polymer dispersions usually also require preservation. The type and scope of preservation will depend on the raw materials used and the anticipated sources of contamination. The compatibility with other components and the efficacy of the preservative should always be tested in the respective formulation. Preservative manufacturers will be able to advise you about the type and dosage of preservative required.
If VINNAPAS® EZ 222 is used in applications other than those mentioned, the choice, processing and use of VINNAPAS® EZ 222 is the sole responsibility of the purchaser. All legal and other regulations must be complied with.
|PRIMIS® KT 3000||- -||50 - 110 mPa·s 50 - 110 mPa·s||大约 1 g/cm³ 大约 1,000 lb/gal||- -||very good very good||- -|
|VINNAPAS® EF 818||- -||150 - 650 mPa·s 150 - 650 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||- -||- -||约 7 °C 约 44.6 °F|
|VINNAPAS® EP 3036 NJG||> 54.5 % > 54.5 %||4400 - 5400 mPa·s 4400 - 5400 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||聚乙烯醇 聚乙烯醇||very good very good||约 0 - 4 °C 约 32.0 - 39.2 °F|
|VINNECO® CT 7030||47 - 49 % 47 - 49 %||800 - 2800 mPa·s 800 - 2800 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||ionic and nonionic surfactants ionic and nonionic surfactants||very good very good||- -|
|VINNECO® EF 3777 (100 MB)||55 - 57 % 55 - 57 %||150 - 1850 mPa·s 150 - 1850 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||surface active emulsifiers surface active emulsifiers||very good very good||- -|
|VINNECO® EF 3777 (60 MB)||55 - 57 % 55 - 57 %||150 - 1850 mPa·s 150 - 1850 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||surface active emulsifiers surface active emulsifiers||very good very good||- -|
|VINNECO® EP 3360 (100 MB)||59 - 61 % 59 - 61 %||3000 - 6000 mPa·s 3000 - 6000 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||离子型和非离子型表 面活性剂及聚合物类 化合物 离子型和非离子型表 面活性剂及聚合物类 化合物||very good very good||约 10 °C 约 50.0 °F|
|VINNECO® EP 3360 (60 MB)||59 - 61 % 59 - 61 %||3000 - 6000 mPa·s 3000 - 6000 mPa·s||大约 1.07 g/cm³ 大约 1,070 lb/gal||离子型和非离子型表 面活性剂及聚合物类 化合物 离子型和非离子型表 面活性剂及聚合物类 化合物||very good very good||约 10 °C 约 50.0 °F|
 与颜料和填料的相容性 | 专用方法,  玻璃化温度 | 专用方法,  保护性胶体/乳化剂体系 | 专用方法