VINNOL® H 15/45 M (Renewable Energy)
VINNOL® H 15/45 M (Renewable Energy) ist ein carboxylgruppenhaltiges Terpolymer aus ca. 84 Gew.% Vinylchlorid (VC) und ca. 15 Gew.% Vinylacetat (VAc) sowie ca. 1 Gew.% Dicarbonsäure.
Das Produkt wird mit einem geringeren PCF (Product Carbon Footprint) hergestellt als die konventionelle VINNOL®-Version. Die elektrische Energie, die bei der Produktion des VINNOL® H 15/45 M (Renewable Energy) benötigt wird, wird vollständig aus erneuerbaren Energiequellen gewonnen, was durch den TÜV Rheinland überprüft und zertifiziert wird.
VINNOL® H 15/45 M (Renewable Energy) (Renewable Energy) ist für Anwendungen im Heißsiegel-, Industriebeschichtungs- und Druckfarben-Bereich geeignet, wobei die gewohnten, herausragenden VINNOL® Produkteigenschaften unverändert bestehen bleiben.
Properties
VINNOL® H 15/45 M (Renewable Energy) ist ein physikalisch trocknendes, thermoplastisches Bindemittel, das durch Verdunsten der in der Formulierung enthaltenen Lösemittel verfilmt.
Wie alle VC-Copolymere weist VINNOL® H 15/45 M (Renewable Energy) hohe Zähigkeit, Dauerflexibilität, Abriebbeständigkeit, geringe Wasserquellbarkeit und geringe Gasdurchlässigkeit auf. Außerdem ist eine gute Beständigkeit gegen Öl, Fett, verdünnte wässrige Säuren, Alkalien und Salzlösungen sowie gegenüber aliphatischen Kohlenwasserstoffen wie Benzin und gegen Alkohole gegeben.
Besondere Merkmale
VINNOL® H 15/45 M (Renewable Energy) weist aufgrund seines Gehalts an Carboxylgruppen ausgezeichnete Metallhaftung auf. Es ist auch als Reaktionspartner bzw. Kombinationsbindemittel in reaktiven Systemen einsetzbar und kann z. B. mit Isocyanaten, Epoxid- oder Melaminharzen vernetzt werden.
Data sheets
Typical applications for VINNOL® H 15/45 M (Renewable Energy):
- Heat-sealable lacquers
- Metal paints
- Paper and film coatings
- Printing inks
- Primers
- Masonry paints
Processing
VINNOL® H 15/45 M (Renewable Energy) is generally used in dissolved form.
Ketones and esters are the solvents most commonly used for VINNOL® H 15/45 M (Renewable Energy), ketones being more efficient than esters.
Of the chlorinated hydrocarbons, methylene chloride and 1,2-dichloroethane are true solvents, while tri- and tetrachloroethene have only a swelling effect. Alcohols and aliphatic hydrocarbons do not dissolve VINNOL® H 15/45 M (Renewable Energy). Aromatic hydrocarbons may be combined to a limited extent with true solvents.
VINNOL® H 15/45 M (Renewable Energy) can be plasticized with monomeric and polymeric plasticizers such as phthalates, adipates, sebacates, citrates, phosphates, epoxides, and chlorinated paraffins.
VINNOL® H 15/45 M (Renewable Energy) is fully compatible with all other VINNOL® surface coating resins. It also combines well with many acrylic polymers and ketone resins, as well as with some epoxides. Alkyd resins, nitrocellulose, polyvinyl acetates and polyvinyl butyrals are in general incompatible with VINNOL® H 15/45 M (Renewable Energy). We recommend always checking the compatibility of VINNOL® H 15/45 M (Renewable Energy) with the polymer in question.
The compatibility of VINNOL® H 15/45 M (Renewable Energy) with pigments or colorants must be checked in preliminary tests. Certain pigments/colorants may produce thixotropic effects and/or impair adhesion. Care must be taken when using pigments containing zinc or cadmium because these catalyze the decomposition of VC copolymers at elevated temperatures. The same applies to iron-oxide pigments.
Despite good inherent stability, it is necessary for some applications to stabilize coatings based on VINNOL® H 15/45 M (Renewable Energy) against heat and/or UV light. Epoxy compounds often suffice to stabilize these coatings against low thermal impact. Where higher temperatures are involved, it is advisable to use calcium/zinc or organotin stabilizers. Outdoor applications require the additional use of UV stabilizers along with thermal stabilizers optimized for these conditions.
To avoid risk of discoloration, contact with iron should be avoided both during preparation of the solution and during subsequent storage of the product. VINNOL®-based surface coating compounds should be stored in coated containers.
The product can be used for applications with food contact in compliance with FDA 21 CFR §175.105 and §175.300.
Comprehensive information regarding evaluation with respect to other food contact regulations may be requested from our account managers and Wacker subsidiaries.
If the product is used in applications other than those mentioned, the choice, processing and use of the product is the sole responsibility of the purchaser. All legal and other regulations must be complied with.
Packaging
Storage
VINNOL® H 15/45 M (Renewable Energy) ist bei Raumtemperatur (unter 25°C) trocken zu lagern. In original verschlossenen Gebinden beträgt die Lagerfähigkeit unter diesen Bedingungen mindestens 12 Monate, beginnend bei Anlieferung. Eine Lagerung über diesen Zeitpunkt hinaus bedeutet nicht notwendigerweise, dass das Produkt unbrauchbar geworden ist. Eine Überprüfung der für den vorgesehenen Einsatzzweck erforderlichen Eigenschaften durch den Anwender ist in diesem Falle jedoch unerlässlich.
Sales and support
34750 Ataşehir / Istanbul
Türkiye
+90 216 569-8210 (Fax)
How can we help you?
- Do you need help in choosing a product or do you require technical support? If so, please contact our experts.