此内容适用于中国大陆。系统检测到您来自美国。您希望将 美国设置为您的新国家吗?

ELASTOSIL® E60 N GREY

ELASTOSIL® E60 N GREY is a flowable one-part silicone rubber for potting and coating applications. When exposed to air moisture it cures at room temperature to yield a permanently flexible silicone rubber with excellent heat resistance.

 

Fully vulcanized ELASTOSIL® E60 N GREY shows long-term stability against weathering, moisture and UV radiation. The silicone elastomer may continously be exposed to constantly changing climatic conditions, UV radiation and temperature as high as 230 °C (446 °F) without damage.



特性

Uncured:

  • Flowable, self-levelling
  • Fast skin formation at room temperature
  • By-product of curing: acetic acid

 

Cured:

  • Medium hardness
  • Designed for coating and potting applications
  • Recommended service temperature range: -50 °C to +230 °C
  • No inhibition of Pt curing silicones
  • Suitable for applications with food contact

 

Please note: fully cured ELASTOSIL® E60 N GREY is suitable for uses under the Recommendation "XV. Silicones" of the BfR and 21 CFR § 175.300 "Resinous and polymeric coatings" and FDA 21 CFR §177.2600 "Rubber articles intended for repeated use", provided that any given limitations on extractable and volatile substances are observed. Residual solvents have to be completely removed from the food contact article.

ELASTOSIL® E60 N GREY的特殊性能

  • 交联性能: 单组分
  • 交联性能: 缩合固化
  • 具体特征: 低粘度
  • 具体特征: 单组分
  • 具体特征: 电绝缘性
  • 具体特征: 缩合固化
  • 具体特征: 耐紫外线性和耐候性
  • 具体特征: 通用型
  • 流变性: 低粘度
  • 监管: 食品级
  • 硫化胶: 电绝缘性
  • 耐久性: 耐紫外线性和耐候性

免责声明

所提供之所有信息均基于我们当前所掌握的知识。尽管如此,我们不对其作任何担保、也不承担任何责任,并且保留在任何时候进行技术变更的权利。购买方应在预测试中对所提供之信息以及产品在既定应用中的适应性进行检查。任何时候都必须以合同条款与条件为准。此外,本免责申明还适用于与第三方权利有关之事宜,尤其是在德国境外。

  • Multipurpose grade for coating and potting, in particular for food related applications
  • Typical fields of application: household appliances, mechanical engineering, bakeware equipment

ELASTOSIL® E60 N GREY is a ready-to-use, one-part silicone rubber which starts curing when exposed to air moisture. Typical curing characteristics are given in the table "Properties Uncured".

 

As RTV-1 silicones require humidity for curing, free access of air moisture to the silicone rubber is essential. Additionally, the vulcanization time of ELASTOSIL® E60 N GREY can be greatly reduced by increasing the level of air's relative humidity. Please note that, unlike the initial skin formation, the total curing rate of RTV-1 silicones is limited by moisture's diffusion speed in silicone rubber.

 

ELASTOSIL® E60 N GREY typically is vulcanized at room temperature. Heat curing is recommended only for applications where the silicone rubber is applied as a thin coating (thickness less than 0.5 mm), because otherwise blistering is likely to occur due to the quick release of acetic acid.

 

After completion of the vulcanization the silicone elastomer may continuously be exposed to constantly changing climatic conditions, UV radiation and high temperature without damage. Cured ELASTOSIL® E60 N GREY usually shows good primerless adhesion to many substrates, e.g. glass, ceramics, metals, plastics and powder coatings.

 

Detailed information about the processing of RTV-1 silicones is given in our brochure “ROOM TEMPERATURE VULCANIZING (RTV) SILICONES - MATERIAL AND PROCESSING GUIDELINES”. We recommend running preliminary tests to optimize conditions for the particular application.

 

Removal:

If removal of the silicone from machines, metering and application equipment is necessary, white spirit or similar nonpolar solvents are recommended. However, cleaning ideally should take place before the silicone rubber is fully vulcanized. Cured silicone needs to be rubbed off or removed mechanically, if necessary in combination with a swelling agent (solvent) or a chemical silicone remover.

Baking Tray Coatings

ELASTOSIL® E60 N GREY is designed to create long-lasting, non-stick coatings for an optimum release of bakery products. Baking trays coated with silicone rubber are particularly suitable for croissants, buns, white bread, brown bread and sourdough bread.

 

Surface Preparation:

Though ELASTOSIL® E60 N GREY shows primerless adhesion to many substrates, the trays to be coated should be cleaned prior use in order to remove any dirt, rust, oil or grease. If required, the surface of the trays can be roughened by sandblasting to improve the adhesion of the silicone rubber coating.

 

Priming:

For an optimum of adhesion it is recommended to additionally prime the trays with WACKER® Primer G 790 or WACKER® Primer G 790 TOLUENE FREE. Both primers are best applied by spraying; dipping or brushing is also suitable.

 

Please note: as a too thick primer layer can reduce adhesion, both WACKER® Primer G 790 and WACKER® Primer G 790 TOLUENE FREE should be applied as a very thin coating only (< 2 µm thickness). In order to minimize the layer thickness, it is recommend to dilute the primers directly before use with a nonpolar and technically dry solvent (cyclohexane, white spirit or a similar aliphatic solvent) in a 1:1 or 1:2 ratio (primer:solvent). Please mind the food compliance of the solvent used for diluting ! For further details regarding priming with WACKER® Primer G 790 or WACKER® Primer G 790 TOLUENE FREE, please revert to the respective technical data sheet.

 

When the primer solution has been applied, the primed parts must be air dried for at least 15 minutes to allow all solvents to evaporate. Finally, the primer layer is baked at 150 to 170 °C for 20 minutes.

 

Preparation of the coating suspension:

Though ELASTOSIL® E60 N GREY is flowable and self-levelling, the product needs to be diluted before use in order to get optimum coating results. Suitable diluents are non-polar, aliphatic solvents such as technically dry cyclohexane, white spirit or a similar aliphatic grade (please mind the food compliance of the solvent used !). A mixing ratio of 1:1 to 2:1 (solvent:silicone rubber) is recommended.

 

Important: once prepared, the coating mixture has to be stirred continously in order to prevent the separation of fillers. Furthermore the container should be humidity-tight and must be kept properly closed, because the coating suspension is sensitive to moisture.

 

Coating:

The coating mixture can be applied by any coating method, such as spraying, dipping and brushing. However, airless spraying equipment is particularly recommended, as this avoids premature curing of the silicone rubber suspension during spraying.

 

Since the film thickness is essential for the durability of the anti-stick coating, the silicone rubber suspension should be applied in a quantity of some 150 g per m² (including overspray). Multilayered application is possible, e.g. for baking pans with a a complex design. In total, the rubber coating should have a thickness of 150 µm (minimum) to 350 µm (maximum) after curing.

 

Curing:

The curing process already starts during application, in the moment when the coating suspension gets in contact with air moisture. For physical drying it is recommended to store the coated trays for at least 60 minutes at room temperature in order to allow the solvents to evaporate. Subsequently the coating is baked at 250 °C for 1 hour (alternatively: 4 hours at 200 °C).

 

Coating removal (deglazing, restoration):

Coated baking trays and pans can be restored either by pyrolysis at a temperature above 600 °C, followed by cleaning via sandblasting, or by chemical methods (immersion into a highly basic etching bath, followed by thoroughly rewashing the trays with water). Alternatively, the silicone rubber coating can be removed by CO₂ blasting or sandblasting.

储存

Store in a dry and cool place.

 

The 'Best use before end' date of each batch is shown on the product label.

 

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

销售和支持

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
中国大陆
+86  21  6130-2000 (电话)
+86 21 6130-2500  (传真)
Contact Sales

我们可以为您提供什么帮助?

  • 您在选择产品方面需要帮助或者需要技术咨询? 请联系我们的专家
Ask a question

您是否需要产品样本?

您可以在此处索取产品样本。

索取样本

更多产品

请选择一个应用程序查看您的产品匹配。

购物车

我的媒体


收藏夹

我的产品