此内容适用于中国。系统检测到您来自美国。您希望将 美国设置为您的新国家吗?

很抱歉,本产品在中国无货。请使用产品搜索联系 我们。

WACKER® HC 100

WACKER® HC 100 is a stable, VOC compliant, 50% actives silicone emulsion that reduces with water to form stable penetrating water repellent emulsions. WACKER® HC 100 was developed to treat a wide variety of mineral substrates including architectural concrete, concrete block, splitface block, pavers, stucco, porous and dense brick, clay tile, and exposed aggregate concrete. It has been found to be particularly effective in Do-It-Yourself (DIY) markets where good water repellency, beading, ease of use and stability are required.

 

WACKER® HC 100 is not recommended for below grade applications where hydrostatic pressure can be significant.



特性

  • Provides excellent water repellency to reduce cracking, spalling, freeze / thaw damage, chemical degradation, biological growth, efflorescence, and dirt pickup, thereby lengthening substrate life maintenance costs
  • Provides excellent beading for improved aesthetics 
  • Superior storage stability including freeze/thaw stability for ease of use.
  • Low VOC emissions on curing; EPA compliant
  • Formulated to minimize darkening effects thus not changing substrate appearances
  • Good stability on highly alkaline surfaces for long term durability
  • Physically and chemically bonds to substrates increasing coating life and making cleaning easier, thereby reducing maintenance costs
  • Applications of WACKER® HC 100 are UV stable and resistant to biological degradation for longer service life leading to less cost for repetitive applications
  • Applications of WACKER® HC 100 are vapor permeable to resist cracking, peeling and blistering, and allowing carbonation to continue after coating application. This lengthens coating and substrate lives and allows for greater substrate structural strength over time
  • Applications of WACKER® HC 100 can improve adhesion of paints to mineral substances thus priming them for painting

免责声明

所提供之所有信息均基于我们当前所掌握的知识。尽管如此,我们不对其作任何担保、也不承担任何责任,并且保留在任何时候进行技术变更的权利。购买方应在预测试中对所提供之信息以及产品在既定应用中的适应性进行检查。任何时候都必须以合同条款与条件为准。此外,本免责申明还适用于与第三方权利有关之事宜,尤其是在德国境外。

WACKER® HC 100 should be blended with water to achieve the desired concentration before application. Tap water may be acceptable for blending. However, due to the chemical variables in tap water, it is recommended that blended samples are tested prior to the use of tap water. Distilled or de-ionized water is recommended. Two coats of the solution should be applied using a "wet-on-wet" procedure to ensure complete coverage. WACKER® HC 100 emulsions can be applied by brushing, spraying or dipping. Maximum water repellency is realized in 72 hours depending on curing conditions. Beading generally improves over time.

 

For most applications dilution rates of 1:4 to 1:9 provide good performance depending on the absorbency of the substrate.

 

A test patch should be performed prior to general application with the customers approval to ensure that desired water repellency and appearance is achieved.

 

Recoatability

 

Substrates which are coated with WACKER® HC 100 at dilution rates of 1:3 or higher (125 ft2/gallon) are generally re-coatable with water and solvent borne paints. WACKER® HC 100 can be used as a primer to provide improved adhesion with paints on mineral substrates.

 

Clean Up

 

Thoroughly rinse application equipment with clean water.

 

 

 

 

 

Disposal

 

WACKER® HC 100 must be disposed according to local, state and federal regulations. WACKER® HC 100 and it's dilutions should be treated as dilute solutions of "silicone resins" which are non-RCRA (Resource Conservation and Recovery Act) or nonhazardous wastes.

Surface Preparation

 

Surface preparation depends on substrate placement, type and strength, curing and finishing processes, age, condition, previous contamination, and the presence of previous coatings as well as the application of WACKER® HC 100. Surfaces should be clean from dust, dirt, oils, grease, curing compounds, other coatings, efflorescence, and laitance before applying WACKER® HC 100. Cleaning methods which are compatible with the application of WACKER® HC 100 include:

 

  • Mechanical - abrasive blasting (sand, baking soda, vacuum).
  • Chemical - acid etching, stripping, solvent de-greasing, caustic soda scrubbing, alkaline soap scrubbing, high pressure washing, high pressure washing with sand.
  • Heat - propane and acetylene torching.

 

If strongly acidic or caustic cleaning agents are used, neutralize the surface and completely wash to remove any residues. Before using any surface preparation method, a test patch should be performed with the customer's approval to ensure that their needs are met.

 

New concrete should be allowed to cure for at least 28 days before applying WACKER® HC 100. In addition, any repair work should be performed at least 3 days before WACKER® HC 100 is applied.

储存

The "Best use before end date" of each batch is shown on the Certificate of Analysis. Storage beyond the date specified on the Certificate of Analysis does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

 

销售和支持

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
中国
+86  21  6130-2000 (电话)
+86 21 6130-2500  (传真)
Contact Sales
网站

我们可以为您提供什么帮助?

    您在选择产品方面需要帮助或者需要技术咨询? 请联系我们的专家
Ask a question

您是否需要产品样本?

您可以在此处索取产品样本。

索取样本