此内容适用于中国。系统检测到您来自美国。您希望将 美国设置为您的新国家吗?

SILRES® BS 3003

SILRES® BS 3003 is a water-thinnable, solventless emulsion, based on a mixture of silane and siloxane.

Diluted solutions of SILRES® BS 3003 serve as highquality, general-purpose water repellents for impregnating and priming mineral surfaces.

Moreover SILRES® BS 3003 can be used for the mass treatment of non-load bearing concrete products.

SILRES® BS 3003 is also suitable for the post-hydrophobation of fiber cement products, such as fiber cement boards.



特性

SILRES® BS 3003 emulsion contains a stabilized mixture of silanes and siloxanes that are susceptible to hydrolysis. Hydrolysis occurs only after application to the substrate, which breaks the emulsion. Alcohol is released and the emulsion is converted into a silicone resin water repellent.

SILRES® BS 3003 reduces the capillary absorption of the building which it has penetrated, but does not clog pores or capillaries. There is therefore little or no impairment of the building material´s ability to breathe.

SILRES® BS 3003 shows the following special features:

  • good depth of penetration
  • resistance to alkalis
  • rapid development of water repellency
  • provides good adhesion for paints
  • water based and environmentally friendly
  • stable in storage, even when diluted

免责声明

所提供之所有信息均基于我们当前所掌握的知识。尽管如此,我们不对其作任何担保、也不承担任何责任,并且保留在任何时候进行技术变更的权利。购买方应在预测试中对所提供之信息以及产品在既定应用中的适应性进行检查。任何时候都必须以合同条款与条件为准。此外,本免责申明还适用于与第三方权利有关之事宜,尤其是在德国境外。

Dilute SILRES® BS 3003 is an excellent water repellent for many absorbent mineral substrates, such as bricks, sand-lime brick, natural sandstone and mineral plasters. It is not so suitable for less absorbent, dense natural stone, especially limestone, marble and reinforced concrete for bridges and roads. Owing to its aqueous consistency and storage stability when diluted, SILRES® BS 3003 is ideal for inplant impregnation of building materials made of clay, aerated concrete, sand-lime brick, fibrous cement, mineral fibers and lightweight aggregate.

SILRES® BS 3003 may also serve as a water-repellent primer for emulsion paints and plasters, silicone resin emulsion paints and silicone resin plasters.
Moreover SILRES® BS 3003 can be used for the mass treatment of non-load bearing concrete products.

Processing

Tap water is suitable for preparing solutions of SILRES® BS 3003 for use as facade water repellent primer. We recommend an active substance content of 5-10% (dilute the product in the ratio 1:5 to 1:11), the exact figure depending on how absorbent the substrate is.

Apply the ready-to-use solution in the usual way:
flooding is the preferred way. Two "wet in wet" coats are needed to ensure complete coverage. Owing to the content of wetting agent in SILRES® BS 3003, reimpregnation at a later date does not present any difficulties.

If it starts raining, stop treatment and cover the freshly impregnated areas.

For the mass impregnation of concrete products an active agent concentration of 10 % per weight is recommended. The dosage of the diluted product can be related to the overall mass or the amount of binding agents of the concrete product. If related to overall mass, a dosage between 0.1 to 1.0 % of the 10 % dilution of SILRES® BS 3003 is recommended. If related to the amount of binding agent, a dosage between 1.0 to 4.0 % of the 10 % dilution of SILRES® BS 3003 is recommended. In order to keep the water-cement-ratio on a constant level, reduce the amount of mixing water by the amount of water added with the diluted emulsion.

Even though an evaluation exhibited no negative influence of SILRES® BS 3003 on the mechanical properties of selected concrete recipes, an independent evaluation of the mechanical properties is recommended.

储存

The 'Best use before end' date of each batch is shown on the product label.

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

The more dilute they are, the more they tend to cream. However, this phase separation may be reversed by brief stirring or agitation. This will restore it to a homogeneous emulsion, without loss of efficacy.

SILRES® BS 3003 contains minor amounts of a preservative that protects the emulsion against microbial contamination and fungal attack. The quality of the water used may make it necessary to add a biocide after dilution in principle, nearly any water-based preservative may be used.

销售和支持

Wacker Chemicals (China) Co.,Ltd.
Caohejing Hi-Tech Park
200233 Shanghai
中国
+86  21  6130-2000 (电话)
+86 21 6130-2500  (传真)
Contact Sales
网站

我们可以为您提供什么帮助?

    您在选择产品方面需要帮助或者需要技术咨询? 请联系我们的专家
Ask a question