This product is not available in United States. Please use the product search or contact us.

DEHESIVE® PSA 810 M

DEHESIVE® PSA 810 M is a solvent-based, addition-curing Silicone Pressure Sensitive Adhesive intended in particularly for coating on films but also for other substrates.



Properties

  • Middle and stable adhesion force
  • Great adhesion force control together with tight adhesion force PSA
  • Excellent cure performance even at lower temperature
  • High flexibility
  • Good resistance to moisture, weathering and aging
  • Excellent wetting performance

Specific features of DEHESIVE® PSA 810 M

  • Regulation: Solvent-based
  • Specific Features: Solvent-based

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

Comprehensive instructions are given in the corresponding Material Safety Data Sheets. They are available on request from WACKER subsidiaries or may be downloaded via WACKER web site http://www.wacker.com.

Data sheets

DEHESIVE® PSA 810 M is a general purpose Silicone PSA for low adhesion level.

In combination with DEHESIVE® PSA 765 KR or DEHESIVE® PSA 846 L or DEHESIVE® PSA 845 T, the adhesion force can be adjusted to higher levels.

Processing

DEHESIVE® PSA 810 M is a thermal-curing system that cures at a web temperature of 90 – 200 °C.

The cure speed depends on formulation (e.g. the amount of Pt-catalyst, type of substrate, setting temperature and effectiveness of the oven).

DEHESIVE® PSA 810 M can be diluted in solvent such as toluene or mixture of toluene/ethyl acetate or toluene/MEK.

The addition of ~1% (w/w) Catalyst PT 5 is required for DEHESIVE® PSA 810 M.

Adhesion promoter can be added to the formulation in case of anchorage performance has to be improved.

Care must be taken to ensure the absence of catalyst poisons in the system. Common poisons are organotin compounds, sulfur compounds (a common source are rolls that have been vulcanized with sulfur), amines, acid amides, zinc stearate and phosphates.

The quality of the coating compound can be ensured by using clean vessels of stainless steel, enamel, plastic or glass to prepare the batch.

Batches of coating compound must be prepared in the order given below.

1. First pour in DEHESIVE® PSA 810 M

2. Add DEHESIVE® PSA 765 KR or DEHESIVE® PSA 846 L or DEHESIVE® PSA 845 T (optionally)

3. Add solvent and stir slowly until the mixture is homogeneous

4. Add Adhesion Promoter (optionally)

5. Slowly stir in catalyst (local over-concentrations must be avoided).

Storage

The 'Best use before end' date of each batch is shown on the product label.

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable.

In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Sales and support

Wacker Chemical Corporation
3301 Sutton Road
Adrian, MI 49221-9397
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

Distributors

No distributors were found for this product

More products

There are no comparable products

Order

My media


My favorites

My products