This product is not available in United States. Please use the product search or contact us.

LUCKY-SILICONE LC 103

WACKER® LC103 is VAE (Vinyl Acetate Ethylene copolymer) water-based sealant suitable for internal cracks exposed to little or no movement. once dried it can be painted if desirable.



Properties

  • Excellent workability
  • Paint applicable
  • No odor(no bad smell)
  • Water based

Disclaimer

All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.

Application Fields

  • Crack repair
  • Paintable joint sealing
  • Joints around indoor plaster
  • Joints exposed to small movement

Restrictions on use

  • It is the user's responsibility to test the compatibility of the sealant with the adjoining materials. Incompatible substances like coating materials (paints, varnishes, and glazes) or organic plasticizer containing rubbers (EPDM, butyl and neoprene) can lead to discoloration or other impairments like loss of adhesion of the sealant. Materials in direct contact with the applied sealant like cleaning agents and materials in indirect contact like gaseous emissions can damage the sealant in its function or change its appearance. Because of the multitude of these materials. Wacker cannot make a general statement to the compatibility of materials with the sealant. In case of doubt the user shall conduct appropriate preliminary tests.
  • WACKER® LC 103 must not be used for insulating glass applications.
  • WACKER® LC 103 should not be used in contact with metals such as lead, copper, brass or zinc due to corrosion.
  • WACKER® LC 103 may be discolored in contact with some WACKER® LC 103, e.g. EPDM, APTK and neoprene.
  • WACKER® LC 103 should not be used for sealing of aquaria.
  • WACKER® LC 103 is not recommended for use on natural stone, such as marble, granite, quartzite, as it can cause staining.
  • WACKER® LC 103 is not recommended for structural glazing bonding.
  • WACKER® LC 103 should not be used in contact with metals such as lead, copper, brass, or zinc due to corrosion.
  • WACKER® LC 103 is not recommended for sealing of aquaria or for longer-term use under water.
  • WACKER® LC 103 is not suitable for food grade applications where the joints are likely to come in contact with food.
  • WACKER® LC 103 is not suitable for use as a mirror adhesive.
  • The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange.

The use of tooling agents should be avoided if possible. Otherwise, water or a diluted solution of a little neutral soap or alcohol in water should be sparingly applied.

 

 

 

Packaging

  • Cartridge: 270ml (25ea/1box), Shelf life is 12 months from production date

 

Storage

The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for theintended use must be checked for quality assurance reasons.

  • Should use before the expire day.
  • Avoid sun light, dry and cool at 5~30°C is recommended.
  • Should be keeping over 0°C.

Sales and support

Wacker Chemical Corporation
3301 Sutton Road
Adrian, MI 49221-9397
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Movement capability Skin Density Modulus at 100 % elongation
ELASTOSIL® 4000 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.02 g/cm³[7] 8.512 lb/gal[7] 0.35 N/mm²[9] 0.35 N/mm²[9]
ELASTOSIL® 4100 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.02 g/cm³[7] 8.512 lb/gal[7] 0.35 N/mm²[9] 0.35 N/mm²[9]
ELASTOSIL® 4103 P 25 %[2] 25 %[2] 20 min[4] 20 min[4] 1.02 g/cm³[8] 8.512 lb/gal[8] 0.35 N/mm²[10] 0.35 N/mm²[10]
ELASTOSIL® 4300 - - 15 min[4] 15 min[4] 1.03 g/cm³[7] 8.596 lb/gal[7] 0.55 N/mm²[9] 0.55 N/mm²[9]
ELASTOSIL® 4500 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.03 g/cm³[7] 8.596 lb/gal[7] 0.45 N/mm²[9] 0.45 N/mm²[9]
ELASTOSIL® 4710 25 %[1] 25 %[1] 15 min[4] 15 min[4] 1.03 g/cm³[7] 8.596 lb/gal[7] 0.37 N/mm²[9] 0.37 N/mm²[9]
ELASTOSIL® 5000 25 %[1] 25 %[1] 20 min[5] 20 min[5] 1.01 g/cm³[7] 8.429 lb/gal[7] 0.38 N/mm²[9] 0.38 N/mm²[9]
ELASTOSIL® 5100 25 %[1] 25 %[1] 20 min[4] 20 min[4] 1.01 g/cm³[7] 8.429 lb/gal[7] 0.38 N/mm²[9] 0.38 N/mm²[9]
ELASTOSIL® 6000 12.5 %[1] 12.5 %[1] 25 min[4] 25 min[4] 0.98 g/cm³[7] 8.178 lb/gal[7] 0.36 N/mm²[9] 0.36 N/mm²[9]
ELASTOSIL® 6100 12.5 %[1] 12.5 %[1] 25 min[4] 25 min[4] 0.98 g/cm³[7] 8.178 lb/gal[7] 0.36 N/mm²[9] 0.36 N/mm²[9]
ELASTOSIL® 6103 P - - - - - 0.36 N/mm²[10] 0.36 N/mm²[10]
ELASTOSIL® 7000 N 25 %[1] 25 %[1] 25 min[4] 25 min[4] 1.03 g/cm³[7] 8.596 lb/gal[7] 0.38 N/mm²[9] 0.38 N/mm²[9]
ELASTOSIL® 7100 P 25 %[1] 25 %[1] 25 min[4] 25 min[4] 1.03 g/cm³[7] 8.596 lb/gal[7] 0.38 N/mm²[9] 0.38 N/mm²[9]
ELASTOSIL® 7750 N 50 %[2] 50 %[2] 20 min[4] 20 min[4] 1.40 g/cm³[7] 11.684 lb/gal[7] 0.40 N/mm²[9] 0.40 N/mm²[9]
ELASTOSIL® 8000 N 50 %[3] 50 %[3] 25 min[4] 25 min[4] 1.02 g/cm³[7] 8.512 lb/gal[7] 0.37 N/mm²[9] 0.37 N/mm²[9]
ELASTOSIL® 8100 P 50 %[3] 50 %[3] 25 min[4] 25 min[4] 1.02 - 1.03 g/cm³[7] 8.512 - 8.596 lb/gal[7] 0.37 N/mm²[9] 0.37 N/mm²[9]
ELASTOSIL® 8510 P 25 %[1] 25 %[1] 15 min[6] 15 min[6] 1.02 g/cm³[7] 8.512 lb/gal[7] 0.35 N/mm²[9] 0.35 N/mm²[9]
ELASTOSIL® 9100 P 20 %[1] 20 %[1] 25 min[4] 25 min[4] 1.0 g/cm³[7] 8.345 lb/gal[7] 0.37 N/mm²[9] 0.37 N/mm²[9]
ELASTOSIL® K760 C ± 50 %[2] ± 50 %[2] 20 min[4] 20 min[4] 1.40 g/cm³[7] 11.684 lb/gal[7] 0.40 N/mm²[9] 0.40 N/mm²[9]
Legend
[1] Movement capability | ISO 11600,  [2] Movement capability | ASTM C920,  [3] Movement capability | ISO 9047,  [4] Skin forming time | 23 °C | 50 % r.h ,  [5] Skin Skin forming time | 23 °C | 50 % r.h ,  [6] Skin formating time | 23 °C | 50 % r.h ,  [7] Density | 23 °C | ISO 1183-1 A,  [8] Density | 23 °C | DIN EN ISO 1183-1 A,  [9] Modulus at 100 % elongation | ISO 8339-A,  [10] Modulus at 100 % elongation | ISO 8339 

Order

My media


My favorites

My products