WACKER® FINISH CT 34 E
WACKER® FINISH CT 34 E is a nonionic micro emulsion of a reactive, aminofunctional silicone fluid.
WACKER® FINISH CT 34 E is particularly suitable as softener for the impregnation of fibers and textiles.
WACKER® FINISH CT 34 E imparts a very soft, smooth and elastic touch to woven and knitted fabrics.
WACKER® FINISH CT 34 E has very little effect on the degree of whiteness.
Generally, no adverse effect on the shade or colour fastness properties of coloured goods is observed.
WACKER® FINISH CT 34 E improves the wash-and -wear properties and the crease recovery angle, sewability and tear strength and reduces abrasion loss. The effects are fast to washing and dry cleaning.
Specific features of WACKER® FINISH CT 34 E
- Product Type: Concentrate
- Regulation: Low volatile
- Specific Features: Dilutable with water
- Specific Features: Low volatile
- Vulcanizate: Easy to use
All the information provided is in accordance with the present state of our knowledge. Nonetheless, we disclaim any warranty or liability whatsoever and reserve the right, at any time, to effect technical alterations. The information provided, as well as the product's fitness for an intended application, should be checked by the buyer in preliminary trials. Contractual terms and conditions always take precedence. This disclaimer of warranty and liability also applies particularly in foreign countries with respect to third parties' rights.
WACKER® FINISH CT 34 E provides permanent effects even without the addition of a catalyst. No specific curing conditions are required if no resins are used.
WACKER® FINISH CT 34 E can be applied either by padding or by the exhaust method but the finishing liquors should not be exposed to high shear as this might cause instability.
5-30 g/l WACKER® FINISH CT 34 E are recommended for the pad method.
For the exhaust method 1-3 %, relative to the weight of goods are adequate and the treatment should be carried out at 40-50°C for 15-20 minutes. The pH of the liquor should not exceed pH 5. It may need to be adjusted with acetic acid.
WACKER® FINISH CT 34 E can be applied either alone or together with resins and other finishing agents.
If WACKER® FINISH CT 34 E is used together with crosslinking agents and other additives, it should be added, in dilute form, after all the other products. (This recommendation applies generally to the processing of all polysiloxanes).
Higher crease recovery angles and lower abrasion values can be obtained in resin finishes by using WACKER® FINISH CT 34 E. A wide range of touches can be obtained by combining WACKER® FINISH CT 34 E with conventional softening agents and other additives such as fillers based on polyacrylate.
Woven and knitted materials of synthetic fibres
0.5 ml/l acetic acid 60 %
10-30 g/l WACKER® FINISH CT 34 E
pad, liquor pick-up about 50 %, dry at 120-150 °C.
Single jersey or interlock cotton fabrics (exhaust method)
0.5 ml/l acetic acid 60 %
2-4 g/l WACKER® FINISH CT 34 E
10-30 minutes at 30-40 °C, without rinsing, hydroextract, dry at 100-150 °C.
- 0.5 kg bottle
- 200 kg drum
- 940 kg IBC
The 'Best use before end' date of each batch is shown on the product label.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons. Emulsions showing signs of creaming should be agitated before use to assure uniform consistency.
Sales and support
How can we help you?
- Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Would you like a product sample?
You can request a product sample here.Request sample
Please choose an application for viewing your product matches.