This product is not available in United States. Please use the product search or contact us.

LUCKY-SILICONE LC 801

WACKER® LC 801 is a one-component, moisture-curing, High modulus silicone sealant with excellent adhesion, very good processing properties for construction including a non-stain (non-bleeding) silicone exclusively for exteriors.

WACKER® LC 801 cures at room temperature in the presence of atmospheric moisture to give a permanently flexible rubber Properties.



Properties

  • Solvent-free
  • Non-sag
  • Recommended for use on natural stone, such as marble, granite, quartzite,
  • Low shrinkage on curing
  • Ready gun ability at low (4 °C) to high (40 °C) temperatures 
  • Tack-free and highly elastic after curing
  • Non-corrosive
  • High modules 
  • Good adhesion with various materials
  • Excellent weather resistance
  • Long shelf life

Application Fields

  • Exterior & interior joint for non stain
  • Al frame curtain wall & complex panel joint
  • Stone & ceramic joint

Processing 

  • Preparation - The substrate areas that will be in contact with the sealant must be clean. For application
  • Masking - To avoid contamination and damage attach a masking tape on the side of work area.
  • Primer - Non-pored substance needs primer treatment at first.
  • Sealing & Tooling - Fully fill in cross point or side edge point of the joint without empty space without bubbles.
  • Curing - Protect from dust and pollutant to have qualified surface and avoid being damaged on the surface of sealant while curing

Certification

  • WACKER® LC 801 is classified KS F 4910 F-25LM / HB(TVOC), Eco-Label certificated. 

Adhesion

  • WACKER® LC 801 exhibits excellent primeless adhesion to most non-porous siliceous material, e.g., glass, tiles, ceramics, concrete. enamel, glazed tiles, and clinker Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties areas, please contact our technical service

Restrictions on use

  • It is the user's responsibility to test the compatibility of the sealant with the adjoining materials. Incompatible substances like coating materials (paints, varnishes, and glazes) or organic plasticizer containing rubbers (EPDM, butyl and neoprene) can lead to discoloration or other impairments like loss of adhesion of the sealant. Materials in direct contact with the applied sealant like cleaning agents and materials in indirect contact like gaseous emissions can damage the sealant in its function or change its appearance. Because of the multitude of these materials. Wacker cannot make a general statement to the compatibility of materials with the sealant. In case of doubt the user shall conduct appropriate preliminary tests.
  • WACKER® LC 801 must not be used for insulating glass applications.
  • WACKER® LC 801 should not be used in contact with metals such as lead, copper, brass or zinc due to corrosion.
  • WACKER® LC 801 may be discolored in contact with some
  • WACKER® LC 801, e.g. EPDM, APTK and neoprene.
  • WACKER® LC 801 should not be used for sealing of aquaria.
  • WACKER® LC 801 is not recommended for structural glazing bonding.
  • WACKER® LC 801 should not be used in contact with metals such as lead, copper, brass, or zinc due to corrosion.
  • WACKER® LC 801 is not recommended for sealing of aquaria or for longer-term use under water.
  • WACKER® LC 801 is not suitable for food grade applications where the joints are likely to come in contact with food.
  • WACKER® LC 801 is not suitable for use as a mirror adhesive.
  • The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange.

The use of tooling agents should be avoided if possible. Otherwise, water or a diluted solution of a little neutral soap or alcohol in water should be sparingly applied.

Packaging

  • Drum:250kg, Shelf life is 24 months since production date.
  • Cartridge: 300ml (25ea/1box), Shelf life is 12 months from production date
  • Sausage: 500ml (20ea/1box), Shelf life is 24 months from production date

Storage

The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

  • Should use before the expire day.
  • Avoid sun light, dry and cool at 5~30°C is recommended.

Sales and support

Wacker Chemical Corporation
3301 Sutton Road
Adrian, MI 49221-9397
United States
+1  888  922-5374 (Phone)
Contact

How can we help you?

  • Do you need help in choosing a product or do you require technical support? If so, please contact our experts.
Ask a question

Would you like a product sample?

You can request a product sample here.

Request sample

More products

Products Technical data
Amine number Density Flash point Modulus at 100 % elongation Movement capability Skin Viscosity, dynamic
CROSSLINKER BO 30 - - - - - - - - - - - - - -
CROSSLINKER BO 32 - - - - - - - - - - - - - -
CROSSLINKER BO 35 - - - - - - - - - - - - - -
CROSSLINKER BO 38 - - - - - - - - - - - - - -
ELASTOSIL® 4000 - - 1.02 g/cm³[7] 8.512 lb/gal[7] - - 0.35 N/mm²[9] 0.35 N/mm²[9] 25 %[1] 25 %[1] 20 min[4] 20 min[4] - -
ELASTOSIL® 4100 - - 1.02 g/cm³[7] 8.512 lb/gal[7] - - 0.35 N/mm²[9] 0.35 N/mm²[9] 25 %[1] 25 %[1] 20 min[4] 20 min[4] - -
ELASTOSIL® 4103 P - - 1.02 g/cm³[8] 8.512 lb/gal[8] - - 0.35 N/mm²[10] 0.35 N/mm²[10] 25 %[2] 25 %[2] 20 min[4] 20 min[4] - -
ELASTOSIL® 4300 - - 1.03 g/cm³[7] 8.596 lb/gal[7] - - 0.55 N/mm²[9] 0.55 N/mm²[9] - - 15 min[4] 15 min[4] - -
ELASTOSIL® 4500 - - 1.03 g/cm³[7] 8.596 lb/gal[7] - - 0.45 N/mm²[9] 0.45 N/mm²[9] 25 %[1] 25 %[1] 20 min[4] 20 min[4] - -
ELASTOSIL® 4710 - - 1.03 g/cm³[7] 8.596 lb/gal[7] - - 0.37 N/mm²[9] 0.37 N/mm²[9] 25 %[1] 25 %[1] 15 min[4] 15 min[4] - -
ELASTOSIL® 5000 - - 1.01 g/cm³[7] 8.429 lb/gal[7] - - 0.38 N/mm²[9] 0.38 N/mm²[9] 25 %[1] 25 %[1] 20 min[5] 20 min[5] - -
ELASTOSIL® 5100 - - 1.01 g/cm³[7] 8.429 lb/gal[7] - - 0.38 N/mm²[9] 0.38 N/mm²[9] 25 %[1] 25 %[1] 20 min[4] 20 min[4] - -
ELASTOSIL® 6000 - - 0.98 g/cm³[7] 8.178 lb/gal[7] - - 0.36 N/mm²[9] 0.36 N/mm²[9] 12.5 %[1] 12.5 %[1] 25 min[4] 25 min[4] - -
ELASTOSIL® 6100 - - 0.98 g/cm³[7] 8.178 lb/gal[7] - - 0.36 N/mm²[9] 0.36 N/mm²[9] 12.5 %[1] 12.5 %[1] 25 min[4] 25 min[4] - -
ELASTOSIL® 6103 P - - - - - - 0.36 N/mm²[10] 0.36 N/mm²[10] - - - - -
ELASTOSIL® 7000 N - - 1.03 g/cm³[7] 8.596 lb/gal[7] - - 0.38 N/mm²[9] 0.38 N/mm²[9] 25 %[1] 25 %[1] 25 min[4] 25 min[4] - -
ELASTOSIL® 7100 P - - 1.03 g/cm³[7] 8.596 lb/gal[7] - - 0.38 N/mm²[9] 0.38 N/mm²[9] 25 %[1] 25 %[1] 25 min[4] 25 min[4] - -
ELASTOSIL® 7750 N - - 1.40 g/cm³[7] 11.684 lb/gal[7] - - 0.40 N/mm²[9] 0.40 N/mm²[9] 50 %[2] 50 %[2] 20 min[4] 20 min[4] - -
ELASTOSIL® 8000 N - - 1.02 g/cm³[7] 8.512 lb/gal[7] - - 0.37 N/mm²[9] 0.37 N/mm²[9] 50 %[3] 50 %[3] 25 min[4] 25 min[4] - -
ELASTOSIL® 8100 P - - 1.02 - 1.03 g/cm³[7] 8.512 - 8.596 lb/gal[7] - - 0.37 N/mm²[9] 0.37 N/mm²[9] 50 %[3] 50 %[3] 25 min[4] 25 min[4] - -
ELASTOSIL® 8510 P - - 1.02 g/cm³[7] 8.512 lb/gal[7] - - 0.35 N/mm²[9] 0.35 N/mm²[9] 25 %[1] 25 %[1] 15 min[6] 15 min[6] - -
ELASTOSIL® 9100 P - - 1.0 g/cm³[7] 8.345 lb/gal[7] - - 0.37 N/mm²[9] 0.37 N/mm²[9] 20 %[1] 20 %[1] 25 min[4] 25 min[4] - -
ELASTOSIL® K760 C - - 1.40 g/cm³[7] 11.684 lb/gal[7] - - 0.40 N/mm²[9] 0.40 N/mm²[9] ± 50 %[2] ± 50 %[2] 20 min[4] 20 min[4] - -
WACKER® ADHESION PROMOTER AMS 60 - - - - > 100 °C > 212 °F - - - - - - 20 - 40 mPa·s 20 - 40 mPa·s
WACKER® ADHESION PROMOTER AMS 61 - - - - > 100 °C > 212 °F - - - - - - approx. 100 mPa·s approx. 100 mPa·s
WACKER® ADHESION PROMOTER AMS 68 approx. 2.5 approx. 2.5 - - 48 °C 118.4 °F - - - - - - - -
WACKER® ADHESION PROMOTER AMS 70 - - - - 55 °C 131 °F - - - - - - approx. 7 mPa·s approx. 7 mPa·s
WACKER® ADHESION PROMOTOR AMS 50 - - - - > 100 °C > 212 °F - - - - - - 15 - 40 mPa·s 15 - 40 mPa·s
WACKER® CATALYST 41 - - - - 38 °C 100.4 °F - - - - - - - -
WACKER® CATALYST AL-T - - - - approx. 10 °C approx. 50.0 °F - - - - - - 2 - 5 mPa·s 2 - 5 mPa·s
WACKER® CATALYST C 88 - - - - 48 °C 118.4 °F - - - - - - - -
WACKER® CROSSLINKER ME 60 - - - - 11 °C 51.8 °F - - - - - - - -
WACKER® CROSSLINKER ME 63 - - - - 11 °C 51.8 °F - - - - - - - -
WACKER® PLASTICIZER 100 - - - - - - - - - - - - 95 - 105 mPa·s 95 - 105 mPa·s
WACKER® PLASTICIZER 1000 - - - - 348 °C 658.4 °F - - - - - - approx. 1000 mPa·s approx. 1000 mPa·s
WACKER® PLASTICIZER MH 30 - - - - approx. 120 °C approx. 248 °F - - - - - - 15 - 50 mPa·s 15 - 50 mPa·s
WACKER® POLYMER AL 08 - - - - 83 °C 181.4 °F - - - - - - approx. 8000 mPa·s approx. 8000 mPa·s
WACKER® POLYMER AL 100 - - - - 90 °C 194 °F - - - - - - approx. 100000 mPa·s approx. 100000 mPa·s
WACKER® POLYMER AL 110 - - - - 90 °C 194 °F - - - - - - approx. 110000 mPa·s approx. 110000 mPa·s
WACKER® POLYMER AL 55 M - - - - 90 °C 194 °F - - - - - - approx. 57000 mPa·s approx. 57000 mPa·s
WACKER® POLYMER AL 60 - - - - 90 °C 194 °F - - - - - - approx. 60000 mPa·s approx. 60000 mPa·s
WACKER® POLYMER FD 120 - - - - - - - - - - - - approx. 120000 mPa·s approx. 120000 mPa·s
WACKER® POLYMER FD 20 - - - - - - - - - - - - approx. 20000 mPa·s approx. 20000 mPa·s
WACKER® POLYMER FD 350 - - - - - - - - - - - - approx. 305000 mPa·s approx. 305000 mPa·s
WACKER® POLYMER FD 50 - - - - - - - - - - - - approx. 50000 mPa·s approx. 50000 mPa·s
WACKER® POLYMER FD 80 - - - - - - - - - - - - approx. 75000 mPa·s approx. 75000 mPa·s
Legend
[1] Movement capability | ISO 11600,  [2] Movement capability | ASTM C920,  [3] Movement capability | ISO 9047,  [4] Skin forming time | 23 °C | 50 % r.h ,  [5] Skin Skin forming time | 23 °C | 50 % r.h ,  [6] Skin formating time | 23 °C | 50 % r.h ,  [7] Density | 23 °C | ISO 1183-1 A,  [8] Density | 23 °C | DIN EN ISO 1183-1 A,  [9] Modulus at 100 % elongation | ISO 8339-A,  [10] Modulus at 100 % elongation | ISO 8339 

Order

My media


My favorites

My products