WACKER® GRUNDIERUNG G 790
WACKER® GRUNDIERUNG G 790 is a solution of reactive siloxanes and silanes in an organic solvent. The primer composition can be applied to the substrate as such or diluted. During evaporation of the solvent and on exposure to atmospheric humidity at ambient temperature a rigid primer film is formed which firmly adheres to the substrate. Application of a silicone rubber onto the primed substrate and subsequent vulcanization will then result in a tight bond between the silicone rubber and the substrate.
- bonding agent preferably used with addition-curing silicone rubbers
- suitable for various coating techniques like dipping, brushing or spraying
Spezifische Merkmale von WACKER® GRUNDIERUNG G 790
- Haftvermittelnde Grundierung
Alle unsere Angaben beruhen auf bestem Wissen. Allerdings übernehmen wir hierfür keine Haftung oder Gewährleistung und behalten uns jederzeit technische Änderungen vor. Es liegt in der eigenen Verantwortung des Käufers, die Angaben sowie die Geeignetheit unseres Produktes für den vorgesehenen Einsatzzweck vor dem Gebrauch zu überprüfen. Vertragliche Regelungen gehen immer vor. Der Gewährleistungs- und Haftungsausschluss gilt - insbesondere im Ausland - auch im Hinblick auf Schutzrechte Dritter.
Bonding agent preferably used with addition-curing silicone rubbers like WACKER® ELASTOSIL® RTV-2 and LSR as well as WACKER® POWERSIL® RTV-2 and LSR.
WACKER® GRUNDIERUNG G 790 is especially suited for bonding addition-curing silicone rubbers to metallic and non-metallic substrates.
Surfaces to be primed have to be dry and free from grease, oil, wax, dust, rust or other contaminants. The surface should be cleaned, e.g. with a non-polar solvent such as mineral spirits (boiling range between 80 °C and 140 °C), followed by a polar solvent, such as acetone. Very smooth surfaces may be roughened by grinding. In case of metals the substrate should be given several hours time to regenerate its oxygen layer before applying the primer. Loose particles must be removed.
The primer can be applied by spraying, immersion or dipping, blade coating or brushing. The primer can be applied as such or diluted with mineral spirits or an alcohol such as ethanol or 2-propanol. In any case, the primer film should be applied as thin as possible and free of air bubbles. Usually the best results can be achieved with a primer layer between 1 and 10 μm thickness corresponding to a coating weigth of 5 to 50 g/m² WACKER® PRIMER G 790. In most cases it is helpful to dilute the primer in organic solvents like white spirits or ISOPAR® E to a ratio of 1 : 1 – 1 : 10.
Evaporation of the solvent should be done at ambient temperature. The formation of a consistent primer film which firmly adheres to the substrate requires a certain atmospheric humidity. Higher or lower humidity will reduce or prolong the necessary reaction time. As a guiding value an evaporation or drying time of 1 – 2 h at ambient temperature and 40 % relative humidity should be applied to allow for a formation of a consistent primer film. In some cases the adhesion can be improved by heating the primered substrate at 100 – 150 °C for up to one hour after evaporation of the solvent at room temperature. Tests should be performed if special conditions are needed.
The silicone rubber should be applied to the primed surface soon after the drying or heating process, if possible. It is recommended that this is done not later than approximately 5 hours after priming the substrate. Otherwise a drop in adhesive strength may occur. Prior to the application of the silicone rubber, the primed surface has to be kept free of contaminations.
Initial adhesion directly after vulcanization of the rubber will in many cases be high already. In some cases, however, initial adhesion will be sufficient for handling the composite while maximum adhesive strength will only be achieved after about 4 days. ELASTOSIL® AUX PRIMERS are sensitive towards humidity. In contact with moisture the liquid primer becomes turbid and the adhesive strength of the primer is impaired. The ELASTOSIL® AUX PRIMERS should therefore be stored in a sealed container after usage.
For detailed information, refer to brochures on www.wacker.com.
The 'Best use before end' date of each batch is shown
on the product label.
Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.