Dieser Inhalt ist für Deutschland bestimmt. Unser System hat erkannt, dass Sie aus USA kommen. Wollen Sie USA als neues Land setzen?


POWERSIL® 552 BRAUNGRÜN is a one-component silicone dispersion that cures to a tough high voltage insulator coating with very good electrical properties.


  • very good resistance to weathering
  • outstanding tracking resistance

Spezifische Merkmale von POWERSIL® 552 BRAUNGRÜN

  • anwendungsfertig
  • Eigenhaftung bei den meisten Untergründen
  • Sehr gutes Hydrophobieverhalten


Alle unsere Angaben beruhen auf bestem Wissen. Allerdings übernehmen wir hierfür keine Haftung oder Gewährleistung und behalten uns jederzeit technische Änderungen vor. Es liegt in der eigenen Verantwortung des Käufers, die Angaben sowie die Geeignetheit unseres Produktes für den vorgesehenen Einsatzzweck vor dem Gebrauch zu überprüfen. Vertragliche Regelungen gehen immer vor. Der Gewährleistungs- und Haftungsausschluss gilt - insbesondere im Ausland - auch im Hinblick auf Schutzrechte Dritter.

Surface pretreatment


The insulator surface to be coated should be clean and free of dust and grease. For cleaning the following operations are suggested:


a) Proper cleaning by using water and a suitable detergent might be sufficient,


b) Insulators that show an adhering pollution, such like cement, other mineral or chemical pollution layers should be cleaned by either “cob corn-“ or carbon dioxide blasting,


c) Any type of grease or fatty pollution is to be removed by using a suitable solvent like White Spirit or turpentine,


d) Residual contaminants should be removed by thoroughly wiping,


e) Finish the cleaning just before spraying POWERSIL® 552 BROWNGREEN with Isopropanol or an equivalent alcohol.


Check carefully that there is no residue of dirt or grease left before spraying!


In most cases it is not necessary to apply a primer before coating.


Proper shaking of drum is mandatory before material is used.


Coating Application


POWERSIL® 552 BROWNGREEN is preferably applied by spraying. It can be applied by brushing or dipping as well. For spraying application, the airless process was found to be efficient. The following equipment settings were found to be suitable:


  • – Flat nozzle of 0.33 mm, 20°
  • – Settings of pressure output 50 – 150 bar


The spray gun should be moved evenly across the surface at a distance of about 30 - 50 cm. Due to the thixotropic properties of POWERSIL® 552 BROWNGREEN it is usually possible to apply the first layer with a good cover. A second layer can be applied after approximately 10-20 minutes.


A typical dry film thickness is 0.4 mm to 0.5 mm. Thus, the theoretical consumption is 0.7 kg to 0.9 kg of POWERSIL® 552 BROWNGREEN per square meter of insulator surface. Take losses for overspray and cleaning of the equipment into consideration.


Rain can damage the coating. In case of rain, please protect the job site or stop application. Full cure is obtained in 8 – 12 hours after coating application depending on thickness, temperature and humidity.


Curing of the coating releases by-products that lead to the formation of siloxanes. These may condensate at the surface, especially at low temperature and low ventilation rate. Therefore it is recommended to process the coating at a temperature above 20°C at well ventilated conditions.


All spraying equipment should be cleaned with a nonpolar solvent (e. g. Xylene or White Spirit) immediately after use.




The product contains migratable matter that is able to encapsulate contaminants and to provide a hydrophobic surface. Coated insulators may appear dirty after some time in service. Nevertheless, washing and cleaning, especially with detergents and other chemicals is not recommended. In case of necessity of any cleaning, we recommend to use POWERSIL® Shine.








The water repellent appearance can be evaluated by spraying with water. IEC 62073, “Guidance on the measurement of wettability of insulator surfaces” provides further information. A partly lowering of the effect does not necessarily require immediate action. Experience shows that the remaining parts of the insulator will provide the necessary insulation ability.


Physical damage, such like scratching can be easily repaired by brushing of fresh coating after partly cleaning with White Spirit.


To allow an instant replacement of broken insulators it is recommendable to store a number of coated spare insulators. These should be stored in a protective covering.


The 'Best use before end' date of each batch is shown on the product label.


Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemie AG
Heilbronner Strasse 74
70191 Stuttgart
+49  711  61942-0 (Phone)
+49 711 61942-61  (Fax)

Wie können wir Ihnen helfen?

    Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Mehr Produkte

Es gibt keine vergleichbaren Produkte