SILRES® BS 36 US

$SILRES<sup>®</sup> BS 36 US

SILRES® BS 36 US is a stable, organo silicone containing water based emulsion. When applied to a surface it forms a stable, penetrating water repellent for enhancing a wide variety of porous mineral substrates including concrete, natural and artificial stone and unglazed ceramic tile.

SILRES® BS 36 US is not recommended for below grade applications where hydrostatic pressure can be significant.



Eigenschaften

  • Provides excellent water repellency to reduce cracking, spalling, freeze/thaw damage, chemical degradation, efflorescence, and dirt pickup, thereby lengthening substrate life and reducing maintenance costs.
  • Enhances the features of the substrate providing a high gloss, wet-look appearance
  • Repels water, reducing penetration while maintaining a consistent appearance
  • Beads liquids
  • Physically and chemically bonds to substrates increasing the service life, making cleaning easier, thereby reducing maintenance costs
  • Improved UV stability
  • Suitable for interior or exterior decorative stone and concrete projects

Surface preparation 
Surface preparation depends on substrate placement, type and strength, curing and finishing processes, age, condition, previous contamination, and the presence of previous coatings. Surfaces should be clean from dust, dirt, oils, grease, curing compounds, other coatings, efflorescence, and laitance before applying SILRES® BS 36 US.

Cleaning methods which are compatible with the application of SILRES® BS 36 US include:

  • Mechanical: abrasive blasting (sand, baking soda, vacuum).
  • Chemical: acid etching, stripping, solvent de-greasing, caustic soda scrubbing, alkaline soap scrubbing, high pressure washing, high pressure washing with sand.
  • Heat: propane and acetylene torching.

 

If strongly acidic or caustic cleaning agents are used, neutralize the surface and completely wash to remove any residues. Before using any surface preparation method, a test patch should be performed with the customer's approval to ensure desired results are achieved.

New concrete should be allowed to cure for at least 28 days before applying SILRES® BS 36 US. Substrate moisture level below 4% promotes penetration of product.


SILRES® BS 36 US is intended to be used at full strength or may be blended with water to desired ratio.

Mix before each use.

SILRES® BS 36 US emulsions can be applied by brush, sponge or roller. Multiple coats may be applied wet-on-wet.

Do not allow product to pool. Remove excess material before it cures.

Water and oil repellency starts to develop within 24 hours.

A test patch should be performed prior to general application with the customer’s approval to ensure that desired appearance, water and oil repellency are achieved. It is advisable to test the product on an inconspicuous area.

Surfaces treated with SILRES® BS 36 US should be cleaned as soon as they have been exposed to contaminant. Paint is very difficult to remove once it has completely cured.

Treated surfaces should be protected from contamination for 24 hours.

Verpackung / Gebinde

Storage

The 'Best use before end' date of each batch is shown on the product label.

Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

The more dilute they are, the more they tend to cream. However, this phase separation may be reversed by brief stirring or agitation. This will restore it to a homogeneous emulsion, without loss of efficacy.

SILRES® BS 36 US contains minor amounts of a preservative that protects the emulsion against microbial contamination and fungal attack. The quality of the water used may make it necessary to add a biocide after dilution in principle, nearly any water-based preservative may be used.

Lagerung

The "Best use before end date" of each batch is shown on the Certificate of Analysis. Storage beyond the date specified on the Certificate of Analysis does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemie AG
Heilbronner Strasse 74
70191 Stuttgart
Deutschland
+49  711  61942-0 (Phone)
+49 711 61942-61  (Fax)
Kontakt

Wie können wir Ihnen helfen?

  • Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Distributoren

WACKER verfügt weltweit über ein Netzwerk fachkundiger Vertriebspartner. Bitte wählen Sie noch eine Anwendung aus damit wir Ihnen Ihre Ansprechpartner nennen können.

IMCD Deutschland GmbH
Konrad-Adenauer-Ufer 41-45
50668 Köln
49  221  77650 (Phone)
49 221 776520  (Fax)
Kontakt Händler Webseite

Bestellen

Meine Medien


Meine Favoriten

Meine Produkte