Dieser Inhalt ist für Deutschland bestimmt. Unser System hat erkannt, dass Sie aus USA kommen. Wollen Sie USA als neues Land setzen?

SILPURAN® 8060/60

SILPURAN® 8060/60 is a peroxide cure, two component high consistency silicone rubber. Vulcanizates are noted for their good flexibility, high transparency and good mechanical properties. SILPURAN® 8060/60 is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY including implantation for < 30 days.



Eigenschaften

SILPURAN® 8060/60 meets selected test requirements of ISO 10993 and United States Pharmacopoeia (USP) Class VI. It is designed for medical applications in compliance with the WACKER SILICONES HEALTH CARE POLICY including implantation for < 30 days.

At service temperatures above approx. 180 °C the addition of suitable heat stabilizers is recommended. Further information about an improvement of the heat stability by use of specific ELASTOSIL® AUX Heat Stabilizers can be obtained from the Technical Information Sheet "ELASTOSIL® AUX Stabilizers H" or the latest edition of our brochures.

Spezifische Merkmale von SILPURAN® 8060/60

  • Lebensmittelkontakt

Disclaimer

Alle unsere Angaben beruhen auf bestem Wissen. Allerdings übernehmen wir hierfür keine Haftung oder Gewährleistung und behalten uns jederzeit technische Änderungen vor. Es liegt in der eigenen Verantwortung des Käufers, die Angaben sowie die Geeignetheit unseres Produktes für den vorgesehenen Einsatzzweck vor dem Gebrauch zu überprüfen. Vertragliche Regelungen gehen immer vor. Der Gewährleistungs- und Haftungsausschluss gilt - insbesondere im Ausland - auch im Hinblick auf Schutzrechte Dritter.

The following studies were performed on vulcanizates of SILPURAN® 8060/60 according to ISO 10993:
    - Cytotoxicity (ISO 10993-5)
    - Sensitation LLNA (ISO 10993-10)
    - Pyrogenicity (ISO 10993-11)

The following studies were performed on vulcanizates of SILPURAN® 8060/60 according to USP class VI:
    - Acute systemic toxicity
    - Intracutaneous toxicity
    - Implantation test
No adverse effects have been detected at any of the studies performed.

Properly cured and post-cured vulcanizates of SILPURAN® 8060/60 can be used for food contact applications and are suitable for use under the Recommendation "XV. Silicones" of the BfR and FDA 21 CFR §177.2600 "Rubber Articles Intended for Repeated Use" considering any given limitations on extractable and volatile substances.

SILPURAN® 8060/60 can be cured by using peroxides, e.g. crosslinker E, C1 and C6 (see table "Cure conditions"). SILPURAN® 8060/60 and the recommended amount of crosslinker are mixed homogeneously on a roll mill. Care must be taken to keep the mill and compound as cool as possible during mixing. Pot life is depending on the used peroxide and storage conditions.

For detailed information please refer to the latest edition of our brochure "SOLID AND LIQUID SILICONE RUBBER - MATERIAL AND PROCESSING GUIDELINES".

Verpackung / Gebinde

SILPURAN® HCR is delivered in blocks (profile diameter = approx. 90 x 100 mm) that are wrapped in an antistatic film and heatsealed in a bag. The customer can thus be sure that the material is not contaminated before it enters the cleanroom. SILPURAN® HCR is packaged in accordance with class 8 clean room standards (DIN EN ISO 14644).

SILPURAN® is neither produced nor packed under sterile conditions, so the final product has to be sterilized prior to use, if necessary.

Lagerung

Please store the cardboard boxes in a dry and cool place. Already opened boxes should be closed again to avoid any contamination.

The 'Best use before end' date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.

Vertrieb & Support

Wacker Chemie AG
Heilbronner Strasse 74
70191 Stuttgart
Deutschland
+49  711  61942-0 (Phone)
+49 711 61942-61  (Fax)
Kontakt

Wie können wir Ihnen helfen?

    Benötigen Sie Unterstützung bei der Produktauswahl oder wünschen Sie eine technische Beratung? Kontaktieren Sie unsere Experten.
Frage stellen

Sie möchten ein Produktmuster?

Hier können Sie ein Produktmuster anfordern.

Muster anfordern

Mehr Produkte

Es gibt keine vergleichbaren Produkte