Our system has noticed that you are based in , but the current country setting is . Do you still want to change your country?

If You Have Questions about Silicone Resin Emulsion Paints, This Is Where You Will Find the Answers.

We have compiled the answers to the most frequently asked questions on silicone resin emulsion paints in the following section.

However new and perfect they may be, most facades contain flaws such as hairline cracks. These are weak spots, where moisture can penetrate the facade. The substrate must be able to dry out whenever ambient conditions permit. Otherwise spalling, or other damage, will occur. Additionally, dry substrates do not promote the growth of microbes, such as algae and fungi.

Silicone resin emulsion paint is a mineral-like coating, it is therefore just as breathable (water-vapor permeable) as silicate paint and whitewash. The reason for this is its microporous structure, which permits the free movement of gases. In the three-tier classification used in European standard EN 1062-1 for water-vapor diffusion current density, silicone resin emulsion paint falls under Class 1 (highly permeable).

Due to the low water uptake, as little water and moisture as possible penetrate the facade. However, no exterior paint offers 100% protection against damp. That’s why it’s important that the paint system features high water-vapor permeability. This is the only way the facade can dry out again. In other words: The masonry can “breathe.”

The combination of these two properties makes silicone resin emulsion paint the prime coating system for facades, and is the reason for their extremely high durability and dirt-repellent effect.

The beading effect becomes apparent during adverse weather (rain, snow, etc.) and is retained throughout the coating’s service life. A treated facade thus keeps its perfect appearance for many years.

The beading effect becomes obvious when it rains: water droplets bead up into little balls and roll off the silicone resin emulsion paint, thus preventing the formation of standing water. This effect ensures an appropriate level of waterproofness. Waterproofness is the property of preventing standing water from penetrating into the substrate even after an extended period of time.

Silicone resin emulsion paints owe their superior durability to the properties of low water absorption combined with high water-vapor permeability. These properties are conferred on the paints by the silicone resin binder, which forms a strongly hydrophobic (water-repellent) network, penetrating deep into the structure of paints and plasters. This permanently protects it against UV light and washout.

Dry facades are less prone to attack by algae, fungi and mold than damp ones. Silicone resin emulsion paints keep facades dry. They are non-thermoplastic, mineral-type coatings and thus provide protection against the growth of microorganisms. For facades that are at great risk, there are silicone resin emulsion paints that contain additional protection against microorganisms.

The binder in silicone resin emulsion paints comprises 50% mineral-type silicone resin and 50% polymer emulsion. The paints thus combine the useful properties of organic and mineral coatings in a single system.

Silicone resin emulsion paints have been used successfully for 40 years. More than a million buildings all over Europe have been coated with these paints, and many of them have endured over 20 years without requiring any further renovation.

Provided they are suitably prepared and cleaned, all kinds of paint can sustain another layer of silicone resin emulsion paint (see also Question 15), including firmly adhering emulsion coatings. However, to avoid compromising the silicone resin emulsion paint’s breathability, old coats of emulsion paint should be stripped off or removed mechanically.

Substrates with salt damage must always be properly repaired first: remove all the damaged substrate, apply repair plaster and a silicone primer. The facade can then be painted with silicone resin emulsion paint.

The paint/substrate interface is the Achilles’ heel of any coating system. This is why a silicone primer is so important for the effectiveness of the paint coating. It creates a dry zone under the paint and thus prevents substances such as alkalis and salts within the construction material from damaging the facade.

Thermal insulation causes a change in surface physics. The facade is heated by the sun from the outside. At night, it cools down. Condensation may occurr, exposing the facade to more moisture.

This nocturnal moisture-induced stress, combined with the fact that the insulation layer reduces the heat flow from the inside out, slows down the rate of drying. As a result, algal growth is often promoted. Thanks to their excellent diffusion properties, silicone resin emulsion paints achieve a significant improvement in such cases.

All coatings containing a wetting agent (emulsion paints and silicone resin emulsion paints) will adhere to silicone resin emulsion paints, but 2-pack silicate paints and whitewash will not.

No (see also Question 10). You merely need to clean the facade, remove any loose particles and, ideally, treat it with a silicone primer. This also applies to old mineral coatings (organosilicate paints).

The quality of an exterior paint is measured by the length of time it protects the facade from external influences and keeps it looking perfect. Silicone resin emulsion paints are unparalleled in these respects, which makes them much more economical in the long term.

Curious About Our SILRES® BS Product Portfolio?

In the product portal you will find all relevant information about our silicone resins.

Discover our products